MC9S12E128CFU Freescale Semiconductor, MC9S12E128CFU Datasheet - Page 377

• Manufacturer Part Number: MC9S12E128CFU
• Description: IC MCU 128K FLASH 25MHZ 80-QFP
• Manufacturer: Freescale Semiconductor
• Series: HCS12r

Specifications of MC9S12E128CFU

• Core Processor: HCS12
• Core Size: 16-Bit
• Speed: 25MHz
• Connectivity: EBI/EMI, I²C, SCI, SPI
• Peripherals: POR, PWM, WDT
• Number Of I /o: 60
• Program Memory Size: 128KB (128K x 8)
• Program Memory Type: FLASH
• Ram Size: 8K x 8
• Voltage - Supply (vcc/vdd): 2.35 V ~ 2.75 V
• Data Converters: A/D 16x10b; D/A 2x8b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 80-QFP
• Data Bus Width: 16 bit
• Data Ram Size: 8 KB
• Interface Type: SCI, SPI
• Maximum Clock Frequency: 25 MHz
• Number Of Programmable I/os: 60
• Number Of Timers: 16 bit
• Operating Supply Voltage: 3.135 V to 5.5 V
• Maximum Operating Temperature: + 85 C
• Mounting Style: SMD/SMT
• Minimum Operating Temperature: - 40 C
• On-chip Adc: 10 bit
• On-chip Dac: 8 bit, 2 Channel
• For Use With: M68EVB912E128 - BOARD EVAL FOR MC9S12E128/64
• Lead Free Status / RoHS Status: Contains lead / RoHS non-compliant
• Eeprom Size: -
• Lead Free Status / Rohs Status: No RoHS Version Available

When the PWMEN bit is cleared:
11.4.8
Fault protection can disable any combination of PWM pins. Faults are generated by a logic one on any of
the FAULT pins. Each FAULT pin can be mapped arbitrarily to any of the PWM pins.
When fault protection hardware disables PWM pins, the PWM generator continues to run, only the output
pins are deactivated.
The fault decoder disables PWM pins selected by the fault logic and the disable mapping register. See
Figure
pin. Refer to
The fault protection is enabled even when the PWM is not enabled; therefore, a fault will be latched in and
will be cleared in order to prevent an interrupt when the PWM is enabled.
11.4.8.1
Each fault pin has a sample filter to test for fault conditions. After every bus cycle setting the FAULTx pin
at logic zero, the filter synchronously samples the pin once every four bus cycles. QSMP determines the
number of consecutive samples that must be logic one for a fault to be detected. When a fault is detected,
the corresponding FAULTx pin flag, FFLAGx, is set. Clear FFLAGx by writing a logic one to it.
If the FIEx, FAULTx pin interrupt enable bit is set, the FFLAGx flag generates a CPU interrupt request.
The interrupt request latch remains set until:
Freescale Semiconductor
•
•
•
•
•
•
•
•
•
•
11-15. Each bank of four bits in the disable mapping register control the mapping for a single PWM
The PWMx outputs will be tri-stated unless OUTCTLx = 1
The PWM counter is cleared and does not count
The PWM generator forces its outputs to zero
The PWMRF flag and pending CPU interrupt requests are not cleared
All fault circuitry remains active unless FPINEx = 0
Software output control remains active
Deadtime insertion continues during software output control
Software clears the FFLAGx flag by writing a logic one to it
Software clears the FIEx bit by writing a logic zero to it
A reset occurs
Fault Protection
Table
Fault Pin Sample Filter
11-12.
MC9S12E128 Data Sheet, Rev. 1.07
Chapter 11 Pulse Width Modulator with Fault Protection (PMF15B6CV2)
377