SI1000-C-GM Silicon Laboratories Inc, SI1000-C-GM Datasheet - Page 175

• Manufacturer Part Number: SI1000-C-GM
• Description: IC TXRX MCU + EZRADIOPRO
• Manufacturer: Silicon Laboratories Inc

Specifications of SI1000-C-GM

• Package / Case: 42-QFN
• Frequency: 240MHz ~ 960MHz
• Data Rate - Maximum: 256kbps
• Modulation Or Protocol: FSK, GFSK, OOK
• Applications: General Purpose
• Power - Output: 20dBm
• Sensitivity: -121dBm
• Voltage - Supply: 1.8 V ~ 3.6 V
• Current - Receiving: 18.5mA
• Current - Transmitting: 85mA
• Data Interface: PCB, Surface Mount
• Memory Size: 64kB Flash, 4kB RAM
• Antenna Connector: PCB, Surface Mount
• Number Of Receivers: 1
• Number Of Transmitters: 1
• Wireless Frequency: 240 MHz to 960 MHz
• Interface Type: UART, SMBus, SPI, PCA
• Output Power: 20 dBm
• Operating Supply Voltage: 0.9 V to 3.6 V
• Maximum Operating Temperature: + 85 C
• Mounting Style: SMD/SMT
• Maximum Supply Current: 4.1 mA
• Minimum Operating Temperature: - 40 C
• Modulation: FSK, GFSK, OOK
• Protocol Supported: C2, SMBus
• Core: 8051
• Program Memory Type: Flash
• Program Memory Size: 64 KB
• Data Ram Size: 4352 B
• Supply Current (max): 4.1 mA
• Cpu Family: Si100x
• Device Core: 8051
• Device Core Size: 8b
• Frequency (max): 25MHz
• Total Internal Ram Size: 4.25KB
• # I/os (max): 22
• Number Of Timers - General Purpose: 4
• Operating Supply Voltage (typ): 2.5/3.3V
• Operating Supply Voltage (max): 3.6V
• Operating Supply Voltage (min): 1.8V
• On-chip Adc: 18-chx10-bit
• Instruction Set Architecture: CISC
• Mounting: Surface Mount
• Pin Count: 42
• Package Type: QFN EP
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Operating Temperature: -
• Lead Free Status / Rohs Status: Lead free / RoHS Compliant
• Other names: 336-1881-5

18. Reset Sources
Reset circuitry allows the controller to be easily placed in a predefined default condition. On entry to this
reset state, the following occur:




All SFRs are reset to the predefined values noted in the SFR descriptions. The contents of RAM are unaf-
fected during a reset; any previously stored data is preserved as long as power is not lost. Since the stack
pointer SFR is reset, the stack is effectively lost, even though the data on the stack is not altered.
The Port I/O latches are reset to 0xFF (all logic ones) in open-drain mode. Weak pullups are enabled dur-
ing and after the reset. For V
exits the reset state.
On exit from the reset state, the program counter (PC) is reset, and the system clock defaults to an internal
oscillator. Refer to Section “19. Clocking Sources” on page 182 for information on selecting and configur-
ing the system clock source. The Watchdog Timer is enabled with the system clock divided by 12 as its
clock source (Section “28.4. Watchdog Timer Mode” on page 363 details the use of the Watchdog Timer).
Program execution begins at location 0x0000.
CIP-51 halts program execution
Special Function Registers (SFRs) are initialized to their defined reset values
External Port pins are forced to a known state
Interrupts and timers are disabled
Px.x
Px.x
SmaRTClock
System
Clock
Comparator 0
RTC0RE
+
-
C0RSEF
Detector
Missing
Clock
(one-
shot)
Microcontroller
EN
DD
Extended Interrupt
CIP-51
Monitor and power-on resets, the RST pin is driven low until the device
Handler
Core
VDD_MCU/DC+
Figure 18.1. Reset Sources
WDT
PCA
EN
System Reset
Supply
Monitor
+
-
Rev. 1.0
Enable
(Software Reset)
SWRSF
(wired-OR)
Power Management
Block (PMU0)
0
Power On
Reset
VBAT
Illegal Flash
Si1000/1/2/3/4/5
Reset
Operation
System Reset
Power-On Reset
*On Si1000/1/2/3 devices,
connected to VDD_MCU.
VBAT is internally
Funnel
Reset
RST
175