SI1000-C-GM Silicon Laboratories Inc, SI1000-C-GM Datasheet - Page 31

• Manufacturer Part Number: SI1000-C-GM
• Description: IC TXRX MCU + EZRADIOPRO
• Manufacturer: Silicon Laboratories Inc

Specifications of SI1000-C-GM

• Package / Case: 42-QFN
• Frequency: 240MHz ~ 960MHz
• Data Rate - Maximum: 256kbps
• Modulation Or Protocol: FSK, GFSK, OOK
• Applications: General Purpose
• Power - Output: 20dBm
• Sensitivity: -121dBm
• Voltage - Supply: 1.8 V ~ 3.6 V
• Current - Receiving: 18.5mA
• Current - Transmitting: 85mA
• Data Interface: PCB, Surface Mount
• Memory Size: 64kB Flash, 4kB RAM
• Antenna Connector: PCB, Surface Mount
• Number Of Receivers: 1
• Number Of Transmitters: 1
• Wireless Frequency: 240 MHz to 960 MHz
• Interface Type: UART, SMBus, SPI, PCA
• Output Power: 20 dBm
• Operating Supply Voltage: 0.9 V to 3.6 V
• Maximum Operating Temperature: + 85 C
• Mounting Style: SMD/SMT
• Maximum Supply Current: 4.1 mA
• Minimum Operating Temperature: - 40 C
• Modulation: FSK, GFSK, OOK
• Protocol Supported: C2, SMBus
• Core: 8051
• Program Memory Type: Flash
• Program Memory Size: 64 KB
• Data Ram Size: 4352 B
• Supply Current (max): 4.1 mA
• Cpu Family: Si100x
• Device Core: 8051
• Device Core Size: 8b
• Frequency (max): 25MHz
• Total Internal Ram Size: 4.25KB
• # I/os (max): 22
• Number Of Timers - General Purpose: 4
• Operating Supply Voltage (typ): 2.5/3.3V
• Operating Supply Voltage (max): 3.6V
• Operating Supply Voltage (min): 1.8V
• On-chip Adc: 18-chx10-bit
• Instruction Set Architecture: CISC
• Mounting: Surface Mount
• Pin Count: 42
• Package Type: QFN EP
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Operating Temperature: -
• Lead Free Status / Rohs Status: Lead free / RoHS Compliant
• Other names: 336-1881-5

GPIO_0
GPIO_1
GPIO_2
ANT_A
Name
XOUT
nIRQ
SDN
RXp
RXn
XIN
NC
TX
Si1000/1
Si1002/3
14, 20,
Table 3.1. Pin Definitions for the Si1000/1/2/3/4/5 (Continued)
Pin Number
24
25
26
11
12
13
22
15
17
18
19
21
Si1004/5
14, 20,
24
25
26
12
13
22
15
17
18
19
21
11
D I/O or
D I/O or
D I/O or
Type
A I/O
A I/O
A I/O
D O
A O
A O
D O
A I
D I
A I
A I
General Purpose I/O controlled by the EZRadioPRO periph-
eral. May be configured through the EZRadioPRO registers
to perform various functions including: Clock Output, FIFO
status, POR, Wake-Up Timer, Low Battery Detect, TRSW,
AntDiversity control, etc. See the EZRadioPRO GPIO Con-
figuration Registers for more information.
EZRadioPRO peripheral interrupt status pin. Will be set low
to indicate a pending EZRadioPRO interrupt event. See the
EZRadioPRO Control Logic Registers for more details. This
pin is an open-drain output with a 220 k internal pullup
resistor. An external pull-up resistor is recommended.
EZRadioPRO peripheral crystal oscillator output. Connect
to an external 30 MHz crystal or leave floating if driving the
XIN pin with an external signal source.
EZRadioPRO peripheral crystal oscillator input. Connect to
an external 30 MHz crystal or to an external source. If using
an external clock source with no crystal, dc coupling with a
nominal 0.8 VDC level is recommended with a minimum
ac amplitude of 700 mVpp.
No Connect. May be left floating or tied to power or ground.
EZRadioPRO peripheral shutdown pin. When driven to
logic HIGH, the EZRadioPRO peripheral will be completely
shut down and the contents of the EZRadioPRO registers
will be lost. This pin should be driven to logic LOW during all
other times; this pin should never be left floating.
EZRadioPRO peripheral transmit RF output pin. The PA
output is an open-drain connection so the L-C match must
supply (1.8 to 3.6 VDC) to this pin.
EZRadioPRO peripheral differential RF input pins of the
LNA. See application schematic for example matching net-
work.
EZRadioPRO peripheral TR switch control signal.
Rev. 1.0
Description
Si1000/1/2/3/4/5
31