SI1000-C-GM Silicon Laboratories Inc, SI1000-C-GM Datasheet - Page 296

• Manufacturer Part Number: SI1000-C-GM
• Description: IC TXRX MCU + EZRADIOPRO
• Manufacturer: Silicon Laboratories Inc

Specifications of SI1000-C-GM

• Package / Case: 42-QFN
• Frequency: 240MHz ~ 960MHz
• Data Rate - Maximum: 256kbps
• Modulation Or Protocol: FSK, GFSK, OOK
• Applications: General Purpose
• Power - Output: 20dBm
• Sensitivity: -121dBm
• Voltage - Supply: 1.8 V ~ 3.6 V
• Current - Receiving: 18.5mA
• Current - Transmitting: 85mA
• Data Interface: PCB, Surface Mount
• Memory Size: 64kB Flash, 4kB RAM
• Antenna Connector: PCB, Surface Mount
• Number Of Receivers: 1
• Number Of Transmitters: 1
• Wireless Frequency: 240 MHz to 960 MHz
• Interface Type: UART, SMBus, SPI, PCA
• Output Power: 20 dBm
• Operating Supply Voltage: 0.9 V to 3.6 V
• Maximum Operating Temperature: + 85 C
• Mounting Style: SMD/SMT
• Maximum Supply Current: 4.1 mA
• Minimum Operating Temperature: - 40 C
• Modulation: FSK, GFSK, OOK
• Protocol Supported: C2, SMBus
• Core: 8051
• Program Memory Type: Flash
• Program Memory Size: 64 KB
• Data Ram Size: 4352 B
• Supply Current (max): 4.1 mA
• Cpu Family: Si100x
• Device Core: 8051
• Device Core Size: 8b
• Frequency (max): 25MHz
• Total Internal Ram Size: 4.25KB
• # I/os (max): 22
• Number Of Timers - General Purpose: 4
• Operating Supply Voltage (typ): 2.5/3.3V
• Operating Supply Voltage (max): 3.6V
• Operating Supply Voltage (min): 1.8V
• On-chip Adc: 18-chx10-bit
• Instruction Set Architecture: CISC
• Mounting: Surface Mount
• Pin Count: 42
• Package Type: QFN EP
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Operating Temperature: -
• Lead Free Status / Rohs Status: Lead free / RoHS Compliant
• Other names: 336-1881-5

Si1000/1/2/3/4/5
296
Bit
MASTER
TXMODE
STA
STO
ACKRQ
ARBLOST
ACK
SI
Set by Hardware When:

















A START is generated.
START is generated.
SMB0DAT is written before the start of an
SMBus frame.
A START followed by an address byte is
received.
A STOP is detected while addressed as a
slave.
Arbitration is lost due to a detected STOP.
A byte has been received and an ACK
response value is needed (only when
hardware ACK is not enabled).
A repeated START is detected as a
MASTER when STA is low (unwanted
repeated START).
SCL is sensed low while attempting to
generate a STOP or repeated START
condition.
SDA is sensed low while transmitting a 1
(excluding ACK bits).
The incoming ACK value is low 
(ACKNOWLEDGE).
A START has been generated.
Lost arbitration.
A byte has been transmitted and an
ACK/NACK received.
A byte has been received.
A START or repeated START followed by a
slave address + R/W has been received.
A STOP has been received.
Table 24.3. Sources for Hardware Changes to SMB0CN
Rev. 1.0
Cleared by Hardware When:











A STOP is generated.
Arbitration is lost.
A START is detected.
Arbitration is lost.
SMB0DAT is not written before the
start of an SMBus frame.
Must be cleared by software.
A pending STOP is generated.
After each ACK cycle.
Each time SI is cleared.
The incoming ACK value is high
(NOT ACKNOWLEDGE).
Must be cleared by software.