SI1000-C-GM Silicon Laboratories Inc, SI1000-C-GM Datasheet - Page 198

• Manufacturer Part Number: SI1000-C-GM
• Description: IC TXRX MCU + EZRADIOPRO
• Manufacturer: Silicon Laboratories Inc

Specifications of SI1000-C-GM

• Package / Case: 42-QFN
• Frequency: 240MHz ~ 960MHz
• Data Rate - Maximum: 256kbps
• Modulation Or Protocol: FSK, GFSK, OOK
• Applications: General Purpose
• Power - Output: 20dBm
• Sensitivity: -121dBm
• Voltage - Supply: 1.8 V ~ 3.6 V
• Current - Receiving: 18.5mA
• Current - Transmitting: 85mA
• Data Interface: PCB, Surface Mount
• Memory Size: 64kB Flash, 4kB RAM
• Antenna Connector: PCB, Surface Mount
• Number Of Receivers: 1
• Number Of Transmitters: 1
• Wireless Frequency: 240 MHz to 960 MHz
• Interface Type: UART, SMBus, SPI, PCA
• Output Power: 20 dBm
• Operating Supply Voltage: 0.9 V to 3.6 V
• Maximum Operating Temperature: + 85 C
• Mounting Style: SMD/SMT
• Maximum Supply Current: 4.1 mA
• Minimum Operating Temperature: - 40 C
• Modulation: FSK, GFSK, OOK
• Protocol Supported: C2, SMBus
• Core: 8051
• Program Memory Type: Flash
• Program Memory Size: 64 KB
• Data Ram Size: 4352 B
• Supply Current (max): 4.1 mA
• Cpu Family: Si100x
• Device Core: 8051
• Device Core Size: 8b
• Frequency (max): 25MHz
• Total Internal Ram Size: 4.25KB
• # I/os (max): 22
• Number Of Timers - General Purpose: 4
• Operating Supply Voltage (typ): 2.5/3.3V
• Operating Supply Voltage (max): 3.6V
• Operating Supply Voltage (min): 1.8V
• On-chip Adc: 18-chx10-bit
• Instruction Set Architecture: CISC
• Mounting: Surface Mount
• Pin Count: 42
• Package Type: QFN EP
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Operating Temperature: -
• Lead Free Status / Rohs Status: Lead free / RoHS Compliant
• Other names: 336-1881-5

Si1000/1/2/3/4/5
20.2.3. Programmable Load Capacitance
The programmable load capacitance has 16 values to support crystal oscillators with a wide range of rec-
ommended load capacitance. If Automatic Load Capacitance Stepping is enabled, the crystal load capaci-
tors start at the smallest setting to allow a fast startup time, then slowly increase the capacitance until the
final programmed value is reached. The final programmed loading capacitor value is specified using the
LOADCAP bits in the RTC0XCF register. The LOADCAP setting specifies the amount of on-chip load
capacitance and does not include any stray PCB capacitance. Once the final programmed loading capaci-
tor value is reached, the LOADRDY flag will be set by hardware to logic 1.
When using the SmaRTClock oscillator in Self-Oscillate mode, the programmable load capacitance can be
used to fine tune the oscillation frequency. In most cases, increasing the load capacitor value will result in
a decrease in oscillation frequency.Table 20.2 shows the crystal load capacitance for various settings of
LOADCAP.
.
198
LOADCAP
0000
0001
0010
0100
0101
1000
1001
1010
0011
0110
0111
1011
1100
1101
1110
1111
Table 20.2. SmaRTClock Load Capacitance Settings
Crystal Load Capacitance
10.5 pF
12.5 pF
13.5 pF
11.5 pF
4.0 pF
4.5 pF
5.0 pF
5.5 pF
6.0 pF
6.5 pF
7.0 pF
7.5 pF
8.0 pF
8.5 pF
9.0 pF
9.5 pF
Rev. 1.0
Equivalent Capacitance seen on
XTAL3 and XTAL4
10.0 pF
12.0 pF
13.0 pF
14.0 pF
15.0 pF
16.0 pF
17.0 pF
18.0 pF
19.0 pF
23.0 pF
25.0 pF
27.0 pF
11.0 pF
21.0 pF
9.0 pF
8.0 pF