SI1000-C-GM Silicon Laboratories Inc, SI1000-C-GM Datasheet - Page 77

• Manufacturer Part Number: SI1000-C-GM
• Description: IC TXRX MCU + EZRADIOPRO
• Manufacturer: Silicon Laboratories Inc

Specifications of SI1000-C-GM

• Package / Case: 42-QFN
• Frequency: 240MHz ~ 960MHz
• Data Rate - Maximum: 256kbps
• Modulation Or Protocol: FSK, GFSK, OOK
• Applications: General Purpose
• Power - Output: 20dBm
• Sensitivity: -121dBm
• Voltage - Supply: 1.8 V ~ 3.6 V
• Current - Receiving: 18.5mA
• Current - Transmitting: 85mA
• Data Interface: PCB, Surface Mount
• Memory Size: 64kB Flash, 4kB RAM
• Antenna Connector: PCB, Surface Mount
• Number Of Receivers: 1
• Number Of Transmitters: 1
• Wireless Frequency: 240 MHz to 960 MHz
• Interface Type: UART, SMBus, SPI, PCA
• Output Power: 20 dBm
• Operating Supply Voltage: 0.9 V to 3.6 V
• Maximum Operating Temperature: + 85 C
• Mounting Style: SMD/SMT
• Maximum Supply Current: 4.1 mA
• Minimum Operating Temperature: - 40 C
• Modulation: FSK, GFSK, OOK
• Protocol Supported: C2, SMBus
• Core: 8051
• Program Memory Type: Flash
• Program Memory Size: 64 KB
• Data Ram Size: 4352 B
• Supply Current (max): 4.1 mA
• Cpu Family: Si100x
• Device Core: 8051
• Device Core Size: 8b
• Frequency (max): 25MHz
• Total Internal Ram Size: 4.25KB
• # I/os (max): 22
• Number Of Timers - General Purpose: 4
• Operating Supply Voltage (typ): 2.5/3.3V
• Operating Supply Voltage (max): 3.6V
• Operating Supply Voltage (min): 1.8V
• On-chip Adc: 18-chx10-bit
• Instruction Set Architecture: CISC
• Mounting: Surface Mount
• Pin Count: 42
• Package Type: QFN EP
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Operating Temperature: -
• Lead Free Status / Rohs Status: Lead free / RoHS Compliant
• Other names: 336-1881-5

5.2.2. Tracking Modes
Each ADC0 conversion must be preceded by a minimum tracking time in order for the converted result to
be accurate. The minimum tracking time is given in Table 4.9. The AD0TM bit in register ADC0CN controls
the ADC0 track-and-hold mode. In its default state when Burst Mode is disabled, the ADC0 input is contin-
uously tracked, except when a conversion is in progress. When the AD0TM bit is logic 1, ADC0 operates in
low-power track-and-hold mode. In this mode, each conversion is preceded by a tracking period of 3 SAR
clocks (after the start-of-conversion signal). When the CNVSTR signal is used to initiate conversions in
low-power tracking mode, ADC0 tracks only when CNVSTR is low; conversion begins on the rising edge of
CNVSTR (see Figure 5.2). Tracking can also be disabled (shutdown) when the device is in low power
standby or sleep modes. Low-power track-and-hold mode is also useful when AMUX settings are fre-
quently changed, due to the settling time requirements described in “5.2.4. Settling Time Requirements” on
page 79.
(AD0CM[2:0]=000, 001,010
Timer 1, Timer 3 Overflow
Figure 5.2. 10-Bit ADC Track and Conversion Example Timing (BURSTEN = 0)
Write '1' to AD0BUSY,
(AD0CM[2:0]=100)
Timer 0, Timer 2,
SAR Clocks
AD0TM=1
AD0TM=0
011, 101)
AD0TM=1
AD0TM=0
CNVSTR
Clocks
Clocks
SAR
SAR
Low Power
or Convert
Low Power
or Convert
Track or
A. ADC0 Timing for External Trigger Source
Convert
Track or Convert
B. ADC0 Timing for Internal Trigger Source
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17
1 2 3 4 5 6 7 8 9 10 11 12 13 14
Track
Track
Rev. 1.0
1 2 3 4 5 6 7 8 9
Convert
Convert
Convert
Convert
10 11 12 13 14
Si1000/1/2/3/4/5
Low Power Mode
Track
Low Power
Mode
Track
77