SI1000-C-GM Silicon Laboratories Inc, SI1000-C-GM Datasheet - Page 373

• Manufacturer Part Number: SI1000-C-GM
• Description: IC TXRX MCU + EZRADIOPRO
• Manufacturer: Silicon Laboratories Inc

Specifications of SI1000-C-GM

• Package / Case: 42-QFN
• Frequency: 240MHz ~ 960MHz
• Data Rate - Maximum: 256kbps
• Modulation Or Protocol: FSK, GFSK, OOK
• Applications: General Purpose
• Power - Output: 20dBm
• Sensitivity: -121dBm
• Voltage - Supply: 1.8 V ~ 3.6 V
• Current - Receiving: 18.5mA
• Current - Transmitting: 85mA
• Data Interface: PCB, Surface Mount
• Memory Size: 64kB Flash, 4kB RAM
• Antenna Connector: PCB, Surface Mount
• Number Of Receivers: 1
• Number Of Transmitters: 1
• Wireless Frequency: 240 MHz to 960 MHz
• Interface Type: UART, SMBus, SPI, PCA
• Output Power: 20 dBm
• Operating Supply Voltage: 0.9 V to 3.6 V
• Maximum Operating Temperature: + 85 C
• Mounting Style: SMD/SMT
• Maximum Supply Current: 4.1 mA
• Minimum Operating Temperature: - 40 C
• Modulation: FSK, GFSK, OOK
• Protocol Supported: C2, SMBus
• Core: 8051
• Program Memory Type: Flash
• Program Memory Size: 64 KB
• Data Ram Size: 4352 B
• Supply Current (max): 4.1 mA
• Cpu Family: Si100x
• Device Core: 8051
• Device Core Size: 8b
• Frequency (max): 25MHz
• Total Internal Ram Size: 4.25KB
• # I/os (max): 22
• Number Of Timers - General Purpose: 4
• Operating Supply Voltage (typ): 2.5/3.3V
• Operating Supply Voltage (max): 3.6V
• Operating Supply Voltage (min): 1.8V
• On-chip Adc: 18-chx10-bit
• Instruction Set Architecture: CISC
• Mounting: Surface Mount
• Pin Count: 42
• Package Type: QFN EP
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Operating Temperature: -
• Lead Free Status / Rohs Status: Lead free / RoHS Compliant
• Other names: 336-1881-5

C2 Register Definition 29.4. FPCTL: C2 Flash Programming Control
C2 Address: 0x02
C2 Register Definition 29.5. FPDAT: C2 Flash Programming Data
C2 Address: 0xB4
Name
Reset
Name
Reset
Bit
7:0
Bit
7:0
Type
Type
Bit
Bit
FPDAT[7:0] C2 Flash Programming Data Register.
FPCTL[7:0] Flash Programming Control Register.
Name
Name
7
0
7
0
This register is used to pass Flash commands, addresses, and data during C2 Flash
accesses. Valid commands are listed below.
Code
0x06
0x07
0x08
0x03
This register is used to enable Flash programming via the C2 interface. To enable C2
Flash programming, the following codes must be written in order: 0x02, 0x01. Note
that once C2 Flash programming is enabled, a system reset must be issued to
resume normal operation.
6
0
6
0
5
0
5
0
Command
Flash Block Read
Flash Block Write
Flash Page Erase
Device Erase
Rev. 1.0
4
0
4
0
FPCTL[7:0]
FPDAT[7:0]
R/W
R/W
Function
Function
3
0
3
0
Si1000/1/2/3/4/5
2
0
2
0
1
0
1
0
0
0
0
0
373