CJ1W-EIP21 Omron, CJ1W-EIP21 Datasheet - Page 236
![no-image](/images/manufacturer_photos/0/4/494/omron_sml.jpg)
CJ1W-EIP21
Manufacturer Part Number
CJ1W-EIP21
Description
Ethernet I/P Module
Manufacturer
Omron
Datasheet
1.CJ1W-EIP21.pdf
(469 pages)
Specifications of CJ1W-EIP21
Lead Free Status / Rohs Status
Lead free / RoHS Compliant
- Current page: 236 of 469
- Download datasheet (10Mb)
Routing Tables
8-4-2
208
PLC #1 (local node)
Connecting and Using a Peripheral Device for the PLC
PLC #1
relay network table
To go to network #3,
first go to node #3 at
network #1.
End
network
2
3
Relay
network
Note
1
1
Note
Node #1
Relay
node
Network #1
3
3
The following example shows routing tables for sending data from PLC #1 (the
local node: network address 1, node address 1) to PLC #4 (the destination
node: network address 3, node address 2).
In the above example, the routing tables required for a message to reach PLC
#4 from PLC #1 are shown. Additional settings would be required in the rout-
ing tables for a message to reach PLC #1 from PLC #4. Refer to 8-4-3 Rout-
ing Table Setting Examples for routing table setting examples.
Routing tables must be created by a CX-Integrator connected to the PLC.
(They cannot be created using a Programming Console.) For details on how
to connect and use the CX-Integrator, refer to the CX-Integrator Operation
Manual (W445). (CX-Integrator is automatically installed when CX-One is
installed.)
1. When routing tables are transferred from the CX-Integrator to the PLC, all
2. To transfer routing tables for multiple nodes to a PLC in one batch, connect
3. Routing tables can only be transferred as a batch to multiple nodes within
PLC #2 (relay node)
End
network
To go to network #3,
first go to node #2 at
network #2.
PLC #2
relay network table
of the CPU Bus Unit are reset so that the routing tables that have been cre-
ated can be read and enabled. Before transferring the routing tables, con-
firm that there will be no problems in the system when the CPU Bus Units
are reset.
the CX-Integrator to a PLC with only one Communications Unit mounted.
Routing tables cannot be transferred to other nodes from a PLC with mul-
tiple Communications Units mounted.
the same network as the PLC to which the CX-Integrator is connected.
Node #2
3
Relay
network
2
Relay
node
Network #2
2
Node #1
Node #3
PLC #3
(relay node)
(To go to network #3
according to the local
network table, go
through unit
number 1 of the local
CPU Rack.)
PLC #3
local network table
Local
network
address
2
3
Network #3
Node #2
Unit #0
Node #1
Unit #1
Unit
number
0
1
End network
(The network is the same,
so go to node #2 at network #3.)
PLC #4 (destination node)
Node #2
Section 8-4
Related parts for CJ1W-EIP21
Image
Part Number
Description
Manufacturer
Datasheet
Request
R
![CJ1W-NC214](/images/manufacturer_photos/0/4/494/omron_tmb.jpg)
Part Number:
Description:
High Speed Pulse Train 2 Axes
Manufacturer:
Omron
Datasheet:
![CJ1W-NC234](/images/manufacturer_photos/0/4/494/omron_tmb.jpg)
Part Number:
Description:
High Speed Pulse Train 2 Axes
Manufacturer:
Omron
Datasheet:
![CJ1W-NC414](/images/manufacturer_photos/0/4/494/omron_tmb.jpg)
Part Number:
Description:
High Speed Pulse Train 4 Axes
Manufacturer:
Omron
Datasheet:
![CJ1W-CT021](/images/manufacturer_photos/0/4/494/omron_tmb.jpg)
Part Number:
Description:
HIGH SPEED COUNTER 500Khz 2 CH
Manufacturer:
Omron
Datasheet:
![G6S-2G](/images/no-image3.png)
Part Number:
Description:
G6S-2GLow Signal Relay
Manufacturer:
Omron Corporation
Datasheet:
![G3NE-220T](/images/no-image3.png)
Part Number:
Description:
Compact, Low-cost, SSR Switching 5 to 20 A
Manufacturer:
Omron Corporation
Datasheet:
![G6K-2G-Y](/images/no-image3.png)
Part Number:
Description:
Manufacturer:
Omron Corporation
Datasheet:
![G4A-1A-E](/images/no-image3.png)
Part Number:
Description:
Manufacturer:
Omron Corporation
Datasheet:
![G5NB-1A-E](/images/no-image3.png)
Part Number:
Description:
Manufacturer:
Omron Corporation
Datasheet:
![G6B-2114P-US](/images/no-image3.png)
Part Number:
Description:
Manufacturer:
Omron Corporation
Datasheet: