LAN9303-ABZJ SMSC, LAN9303-ABZJ Datasheet - Page 153

• Manufacturer Part Number: LAN9303-ABZJ
• Description: IC ETHER SW 3PORT 16BIT 56QFN
• Manufacturer: SMSC

Specifications of LAN9303-ABZJ

• Controller Type: Ethernet Switch Controller
• Interface: SMBus (2-Wire/I²C)
• Voltage - Supply: 3 V ~ 3.6 V
• Current - Supply: 190mA
• Operating Temperature: 0°C ~ 70°C
• Mounting Type: Surface Mount
• Package / Case: 56-QFN
• Product: Ethernet Switches
• Standard Supported: Yes
• Data Rate: 10 Mbps/100 Mbps
• Supply Voltage (max): 3.6 V
• Supply Voltage (min): 3 V
• Supply Current (max): 0.19 A (Typ)
• Maximum Operating Temperature: + 70 C
• Minimum Operating Temperature: 0 C
• Mounting Style: SMD/SMT
• For Use With: 638-1095 - EVALUATION BOARD FOR LAN9303
• Lead Free Status / Rohs Status: Lead free / RoHS Compliant
• Other names: 638-1082

Small Form Factor Three Port 10/100 Managed Ethernet Switch with Single MII/RMII/Turbo MII
Datasheet
SMSC LAN9303/LAN9303i
BITS
1
0
Port 1 Full-Duplex Transmit Flow Control Enable (TX_FC_1)
When the MANUAL_FC_1 bit is set, or Auto-Negotiation is disabled, this bit
enables/disables full-duplex Pause packets to be generated on switch Port
1.
0: Disable flow control transmit
1: Enable flow control transmit
Port 1 Full-Duplex Manual Flow Control Select (MANUAL_FC_1)
This bit toggles flow control selection between manual and auto-negotiation.
0: If auto-negotiation is enabled, the auto-negotiation function
determines the flow control of switch Port 1 (RX_FC_1 and TX_FC_1
values ignored). If auto-negotiation is disabled, the RX_FC_1 and
TX_FC_1 values are used.
1: TX_FC_1 and RX_FC_1 bits determine the flow control of switch Port
1 when in full-duplex mode.
Note 13.4 The default value of this field is determined by the
Note 13.5 The default value of this bit is determined by multiple strap settings. The strap values are
Note 13.6 The default value of this field is determined by the
Note 13.7 The default value of this field is determined by the
strap values are loaded during reset and can be re-written by the EEPROM Loader. Once
the EEPROM Loader re-writes the values, this register is updated with the new values.
See
loaded during reset and can be re-written by the EEPROM Loader. Once the EEPROM
Loader re-writes the values, this register is updated with the new values. Refer to
6.2.3, "Flow Control Enable Logic," on page 62
strap values are loaded during reset and can be re-written by the EEPROM Loader. Once
the EEPROM Loader re-writes the values, this register is updated with the new values.
See
The strap values are loaded during reset and can be re-written by the EEPROM Loader.
Once the EEPROM Loader re-writes the values, this register is updated with the new
values. See
Section 4.2.4, "Configuration Straps," on page 45
Section 4.2.4, "Configuration Straps," on page 45
Section 4.2.4, "Configuration Straps," on page 45
DESCRIPTION
DATASHEET
153
for additional information.
BP_EN_strap_1
FD_FC_strap_1
manual_FC_strap_1
for more information.
for more information.
for more information.
TYPE
R/W
R/W
configuration strap. The
configuration strap. The
Revision 1.4 (07-07-10)
configuration strap.
DEFAULT
Note 13.6
Note 13.7
Section