AT32UC3A3128 Atmel Corporation, AT32UC3A3128 Datasheet - Page 29

• Manufacturer Part Number: AT32UC3A3128
• Manufacturer: Atmel Corporation

Specifications of AT32UC3A3128

• Flash (kbytes): 128 Kbytes
• Pin Count: 144
• Max. Operating Frequency: 66 MHz
• Cpu: 32-bit AVR
• # Of Touch Channels: 32
• Hardware Qtouch Acquisition: No
• Max I/o Pins: 110
• Ext Interrupts: 110
• Usb Transceiver: 1
• Usb Speed: Hi-Speed
• Usb Interface: Device + OTG
• Spi: 6
• Twi (i2c): 2
• Uart: 4
• Lin: 4
• Ssc: 1
• Sd / Emmc: 1
• Graphic Lcd: No
• Video Decoder: No
• Camera Interface: No
• Adc Channels: 8
• Adc Resolution (bits): 10
• Adc Speed (ksps): 384
• Resistive Touch Screen: No
• Dac Channels: 2
• Dac Resolution (bits): 16
• Temp. Sensor: No
• Crypto Engine: No
• Sram (kbytes): 128
• Self Program Memory: YES
• External Bus Interface: 1
• Dram Memory: sdram
• Nand Interface: Yes
• Picopower: No
• Temp. Range (deg C): -40 to 85
• I/o Supply Class: 3.0 to 3.6
• Operating Voltage (vcc): 3.0 to 3.6
• Fpu: No
• Mpu / Mmu: Yes / No
• Timers: 6
• Output Compare Channels: 18
• Input Capture Channels: 12
• Pwm Channels: 12
• 32khz Rtc: Yes
• Calibrated Rc Oscillator: Yes

3.9.1.2
3.9.1.3
3.9.1.4
3.9.1.5
32002F–03/2010
Unrecoverable Exception
TLB Multiple Hit Exception
OCD Stop CPU Exception
Bus Error Exception on Data Access
All other system registers are reset to their reset value, which may or may not be defined. Refer
to the Programming Model chapter for details.
The OCD Stop CPU exception is generated when the OCD Stop CPU input line to the CPU is
asserted. The OCD Stop CPU exception can not be masked by any bit. This exception is identi-
cal to a non-maskable, high priority breakpoint. Any subsequent operation is controlled by the
OCD hardware. The OCD hardware will take control over the CPU and start to feed instructions
directly into the pipeline.
The Unrecoverable Exception is generated when an exception request is issued when the
Exception Mask (EM) bit in the status register is asserted. The Unrecoverable Exception can not
be masked by any bit. The Unrecoverable Exception is generated when a condition has
occurred that the hardware cannot handle. The system will in most cases have to be restarted if
this condition occurs.
The TLB Multiple Hit Exception is generated when an access hits in multiple MPU regions. This
is usually caused by programming error. Used only if an MPU is present.
The Bus Error on Data Access exception is generated when the data bus detects an error condi-
tion. This exception is caused by events unrelated to the instruction stream, or by data written to
the cache write-buffers many cycles ago. Therefore, execution can not be resumed in a safe
way after this exception. The return address placed on stack is unrelated to the operation that
PC = 0x8000_0000;
RSR_DBG = SR;
RAR_DBG = PC;
SR[M2:M0] = B’110;
SR[D] = 1;
SR[DM] = 1;
SR[EM] = 1;
SR[GM] = 1;
*(--SP
*(--SP
SR[M2:M0] = B’110;
SR[EM] = 1;
SR[GM] = 1;
PC = EVBA | 0x00;
*(--SP
*(--SP
SR[M2:M0] = B’110;
SR[EM] = 1;
SR[GM] = 1;
PC = EVBA | 0x04;
SYS
SYS
SYS
SYS
) = PC of offending instruction;
) = SR;
) = PC of offending instruction;
) = SR;
AVR32
29