AT32UC3A3128 Atmel Corporation, AT32UC3A3128 Datasheet - Page 84

• Manufacturer Part Number: AT32UC3A3128
• Manufacturer: Atmel Corporation

Specifications of AT32UC3A3128

• Flash (kbytes): 128 Kbytes
• Pin Count: 144
• Max. Operating Frequency: 66 MHz
• Cpu: 32-bit AVR
• # Of Touch Channels: 32
• Hardware Qtouch Acquisition: No
• Max I/o Pins: 110
• Ext Interrupts: 110
• Usb Transceiver: 1
• Usb Speed: Hi-Speed
• Usb Interface: Device + OTG
• Spi: 6
• Twi (i2c): 2
• Uart: 4
• Lin: 4
• Ssc: 1
• Sd / Emmc: 1
• Graphic Lcd: No
• Video Decoder: No
• Camera Interface: No
• Adc Channels: 8
• Adc Resolution (bits): 10
• Adc Speed (ksps): 384
• Resistive Touch Screen: No
• Dac Channels: 2
• Dac Resolution (bits): 16
• Temp. Sensor: No
• Crypto Engine: No
• Sram (kbytes): 128
• Self Program Memory: YES
• External Bus Interface: 1
• Dram Memory: sdram
• Nand Interface: Yes
• Picopower: No
• Temp. Range (deg C): -40 to 85
• I/o Supply Class: 3.0 to 3.6
• Operating Voltage (vcc): 3.0 to 3.6
• Fpu: No
• Mpu / Mmu: Yes / No
• Timers: 6
• Output Compare Channels: 18
• Input Capture Channels: 12
• Pwm Channels: 12
• 32khz Rtc: Yes
• Calibrated Rc Oscillator: Yes

8.18
8.19
8.19.1
32002F–03/2010
Read-modify-write instructions
Code example
Assumptions
Table 8-14.
This group contains instructions that perform atomical bit-operations on memory addresses.
These instructions require multiple cycles inside the memory controller, but these can be per-
formed in parallel with subsequent instructions if the following instructions are not memory
access instructions.
A RMW instruction performed on an address in the IRAM section executes in a single cycle if the
IRAM write buffer is empty. If the write buffer is not empty, two cycles are required. The pro-
grammer can make sure the buffer is empty by ensuring that the instruction immediately before
the RMW instruction is not a store or another RMW instruction.
If the RMW instruction is performed on an address in the HSB section, four cycles are needed
for the RMW instruction to be executed. Therefore, if another instruction attempts to access
memory within one of the three following clock cycles, up to three stall cycles will be inserted. If
a memory access instruction is scheduled less than 3 cycles after the RMW to HSB instruction,
3-n stall cycles are inserted. Here n is the number of cycles used by instructions between the
RMW instruction and the first memory access instruction. RMW operations to the HSB section
will take additional cycles if the HSB inserts wait states.
When using RMW instructions, try to schedule code so that stall cycles are avoided.
Table 8-15.
In the example code given in this chapter, the following assumptions are made:
pref
sleep
sync
Mnemonics
memc
mems
memt
• r0 points to an address in the IRAM space. IRAM is an alias for r0.
• r1 points to an address in the HSB or BOOT space. HSB is an alias for r1.
• All memories and buses have 0 wait state access.
• The CPU is in a priviliged mode, so that no privilege violations occur
System control instructions
Read-modify-write instructions to IRAM section
E
E
E
E
E
E
Rp[disp]
Op8
Op8
Operands
imm, bp
imm, bp
imm, bp
Description
Clear bit in memory.
Set bit in memory.
Toggle bit in memory.
Prefetch cache line.
Enter SLEEP mode.
Flush write buffer.
Execution
cycles IRAM
1/2
1/2
1/2
Execution
cycles HSB
4
4
4
AVR32
1
1
1
84