AT91SAM9RL64-CU Atmel, AT91SAM9RL64-CU Datasheet - Page 588

• Manufacturer Part Number: AT91SAM9RL64-CU
• Description: IC ARM9 MCU 217-LFBGA
• Manufacturer: Atmel
• Series: AT91SAMr

Specifications of AT91SAM9RL64-CU

• Core Processor: ARM9
• Core Size: 16/32-Bit
• Speed: 240MHz
• Connectivity: EBI/EMI, I²C, MMC, SPI, SSC, UART/USART, USB
• Peripherals: AC'97, LCD, POR, PWM, WDT
• Number Of I /o: 118
• Program Memory Size: 32KB (32K x 8)
• Program Memory Type: ROM
• Ram Size: 72K x 8
• Voltage - Supply (vcc/vdd): 1.08 V ~ 1.32 V
• Data Converters: A/D 6x10b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 217-LFBGA
• Processor Series: AT91SAMx
• Core: ARM926EJ-S
• Data Bus Width: 32 bit
• Data Ram Size: 64 KB
• Interface Type: 2-Wire, SPI, SSC, USART
• Maximum Clock Frequency: 240 MHz
• Number Of Programmable I/os: 118
• Number Of Timers: 4
• Maximum Operating Temperature: + 85 C
• Mounting Style: SMD/SMT
• 3rd Party Development Tools: JTRACE-ARM-2M, MDK-ARM, RL-ARM, ULINK2
• Development Tools By Supplier: AT91SAM-ICE, AT91-ISP
• Minimum Operating Temperature: - 40 C
• On-chip Adc: 10 bit, 6 Channel
• Controller Family/series: AT91SAM9xxx
• No. Of I/o's: 118
• Ram Memory Size: 64KB
• Cpu Speed: 240MHz
• No. Of Timers: 1
• Rohs Compliant: Yes
• Package: 217LFBGA
• Device Core: ARM926EJ-S
• Family Name: 91S
• Maximum Speed: 240 MHz
• Operating Supply Voltage: 1.8|3.3 V
• For Use With: AT91SAM9RL-EK - KIT EVAL FOR AT91SAM9RLAT91SAM-ICE - EMULATOR FOR AT91 ARM7/ARM9
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Eeprom Size: -
• Lead Free Status / Rohs Status: Lead free / RoHS Compliant

6289C–ATARM–28-May-09
The transfer is similar to that shown in
The DMAC Transfer flow is shown in
4. After the DMAC channel has been programmed, enable the channel by writing a ‘1’ to
5. When the buffer transfer has completed, the DMAC reloads the DMAC_SADDRx regis-
6. The DMAC transfer proceeds as follows:
e. If source picture-in-picture is enabled (DMAC_CTRLBx.SPIP is enabled), program
f.
g. Write the channel configuration information into the DMAC_CFGx register for chan-
the DMAC_CHER.ENABLE[n] bit where n is the channel number. Make sure that bit 0
of the DMAC_EN.ENABLE register is enabled.
ter. The DMAC_DADDRx register remains unchanged. Hardware sets the buffer
complete interrupt. The DMAC then samples the row number as shown in
on page
ware sets the transfer complete interrupt and disables the channel. So you can either
respond to the Buffer Complete or Transfer Complete interrupts, or poll for ENABLE
field in the Channel Status Register (DMAC_CHSR.ENABLE[n] bit) until it is cleared by
hardware, to detect when the transfer is complete. If the DMAC is not in Row 1, the next
step is performed.
a. If the buffer complete interrupt is un-masked (DMAC_EBCIMR.BTC[x] = ‘1’, where
b. If the buffer complete interrupt is masked (DMAC_EBCIMR.BTC[x] = ‘1’, where x is
– Source AHB master interface layer in the SIF field where source resides.
– Destination AHB master interface master layer in the DIF field where destination
resides.
– Incrementing/decrementing or fixed address for source in SRC_INCR field.
– Incrementing/decrementing or fixed address for destination in DST_INCR field.
the DMAC_SPIPx register for channel x.
If destination picture-in-picture is enabled (DMAC_CTRLBx.DPIP), program the
DMAC_DPIPx register for channel x.
nel x.
x is the channel number) hardware sets the buffer complete interrupt when the buf-
fer transfer has completed. It then stalls until STALLED[n] bit of DMAC_CHSR is
cleared by writing in the KEEPON[n] field of DMAC_CHER register where n is the
channel number. If the next buffer is to be the last buffer in the DMAC transfer, then
the buffer complete ISR (interrupt service routine) should clear the automatic mode
bit, DMAC_CTRLBx.AUTO. This puts the DMAC into Row 1 as shown in
1 on page
automatic transfer mode bit should remain enabled to keep the DMAC in Row 11 as
shown in
the channel number) then hardware does not stall until it detects a write to the buf-
fer transfer completed interrupt enable register but starts the next buffer transfer
immediately. In this case software must clear the automatic mode bit,
DMAC_CTRLBx.AUTO, to put the device into ROW 1 of
before the last buffer of the DMAC transfer has completed.
575. If the DMAC is in Row 1, then the DMAC transfer has completed. Hard-
Table 37-1 on page
575. If the next buffer is not the last buffer in the DMAC transfer then the
AT91SAM9R64/RL64 Preliminary
Figure 37-13 on page
Figure 37-12 on page
575.
590.
589.
Table 37-1 on page 575
Table 37-1
Table 37-
588