AT91SAM9RL64-CU Atmel, AT91SAM9RL64-CU Datasheet - Page 82

• Manufacturer Part Number: AT91SAM9RL64-CU
• Description: IC ARM9 MCU 217-LFBGA
• Manufacturer: Atmel
• Series: AT91SAMr

Specifications of AT91SAM9RL64-CU

• Core Processor: ARM9
• Core Size: 16/32-Bit
• Speed: 240MHz
• Connectivity: EBI/EMI, I²C, MMC, SPI, SSC, UART/USART, USB
• Peripherals: AC'97, LCD, POR, PWM, WDT
• Number Of I /o: 118
• Program Memory Size: 32KB (32K x 8)
• Program Memory Type: ROM
• Ram Size: 72K x 8
• Voltage - Supply (vcc/vdd): 1.08 V ~ 1.32 V
• Data Converters: A/D 6x10b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 217-LFBGA
• Processor Series: AT91SAMx
• Core: ARM926EJ-S
• Data Bus Width: 32 bit
• Data Ram Size: 64 KB
• Interface Type: 2-Wire, SPI, SSC, USART
• Maximum Clock Frequency: 240 MHz
• Number Of Programmable I/os: 118
• Number Of Timers: 4
• Maximum Operating Temperature: + 85 C
• Mounting Style: SMD/SMT
• 3rd Party Development Tools: JTRACE-ARM-2M, MDK-ARM, RL-ARM, ULINK2
• Development Tools By Supplier: AT91SAM-ICE, AT91-ISP
• Minimum Operating Temperature: - 40 C
• On-chip Adc: 10 bit, 6 Channel
• Controller Family/series: AT91SAM9xxx
• No. Of I/o's: 118
• Ram Memory Size: 64KB
• Cpu Speed: 240MHz
• No. Of Timers: 1
• Rohs Compliant: Yes
• Package: 217LFBGA
• Device Core: ARM926EJ-S
• Family Name: 91S
• Maximum Speed: 240 MHz
• Operating Supply Voltage: 1.8|3.3 V
• For Use With: AT91SAM9RL-EK - KIT EVAL FOR AT91SAM9RLAT91SAM-ICE - EMULATOR FOR AT91 ARM7/ARM9
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Eeprom Size: -
• Lead Free Status / Rohs Status: Lead free / RoHS Compliant

14.7.3.2
14.8
6289C–ATARM–28-May-09
Hardware and Software Constraints
Communication Endpoints
The device also handles some class requests defined in the CDC class.
Table 14-4.
Unhandled requests are STALLed.
There are two communication endpoints and endpoint 0 is used for the enumeration process.
Endpoint 1 is a 512-byte Bulk OUT endpoint and endpoint 2 is a 512-byte Bulk IN endpoint.
SAM-BA Boot commands are sent by the host through the endpoint 1. If required, the message
is split by the host into several data payloads by the host driver.
If the command requires a response, the host can send IN transactions to pick up the response.
The MCI, the SPI and NAND Flash drivers use several PIOs in alternate functions to communi-
cate with devices. Care must be taken when these PIOs are used by the application. The
devices connected could be unintentionally driven at boot time, and electrical conflicts between
peripherals output pins and the connected devices may appear.
To assure correct functionality, it is recommended to plug in critical devices to other pins.
Table 14-5
are driven during the boot sequence for a period of less than 1 second if no correct boot program
is found.
For the DataFlash driven by the SPCK signal at 8 MHz, the time to download 60 K bytes is
reduced to 200 ms.
Request
SET_LINE_CODING
GET_LINE_CODING
SET_CONTROL_LINE_STATE
• A 12 MHz Crystal is mandatory in order to generate correctly 480 MHz clock necessary for
• No Bypass Mode.
• The SD Card, NAND Flash and DataFlash downloaded code size must be inferior to 56 K
• The code is always downloaded from the DataFlash or NAND Flash device address
• The downloaded code must be position-independent or linked at address 0x0000_0000.
• The DataFlash must be connected to NPCS0 of the SPI.
the USB High Speed Device and to generate the 48 MHz System clock.
bytes.
0x0000_0000 to the address 0x0000_0000 of the internal SRAM (after remap).
contains a list of pins that are driven during the boot program execution. These pins
Handled Class Requests
AT91SAM9R64/RL64 Preliminary
Definition
Configures DTE rate, stop bits, parity and number of
character bits.
Requests current DTE rate, stop bits, parity and number
of character bits.
RS-232 signal used to tell the DCE device the DTE
device is now present.
82