S9S12XS256J0CAL Freescale Semiconductor, S9S12XS256J0CAL Datasheet - Page 198

• Manufacturer Part Number: S9S12XS256J0CAL
• Description: MCU 256K FLASH 112-LQFP
• Manufacturer: Freescale Semiconductor
• Series: HCS12r

Specifications of S9S12XS256J0CAL

• Core Processor: HCS12X
• Core Size: 16-Bit
• Speed: 40MHz
• Connectivity: CAN, SCI, SPI
• Peripherals: LVD, POR, PWM, WDT
• Number Of I /o: 91
• Program Memory Size: 256KB (256K x 8)
• Program Memory Type: FLASH
• Eeprom Size: 8K x 8
• Ram Size: 12K x 8
• Voltage - Supply (vcc/vdd): 1.72 V ~ 5.5 V
• Data Converters: A/D 16x12b
• Oscillator Type: External
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 112-LQFP
• Processor Series: S12XS
• Core: HCS12
• Data Bus Width: 16 bit
• Data Ram Size: 12 KB
• Interface Type: CAN, SCI, SPI
• Maximum Clock Frequency: 40 MHz
• Number Of Programmable I/os: 91
• Number Of Timers: 12
• Maximum Operating Temperature: + 85 C
• Mounting Style: SMD/SMT
• 3rd Party Development Tools: EWHCS12
• Development Tools By Supplier: DEMO9S12XSFAME, EVB9S12XEP100
• Minimum Operating Temperature: - 40 C
• On-chip Adc: 12 bit, 16 Channel
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant

S12X Debug (S12XDBGV3) Module
6.3.2.1
Read: Anytime
Write: Bits 7, 1, 0 anytime
198
Address: 0x0020
reserved
Reset
Field
TRIG
ARM
BDM
7
6
5
4
W
R
Bit 6 can be written anytime but always reads back as 0.
Bits 5:2 anytime S12XDBG is not armed.
ARM
Arm Bit — The ARM bit controls whether the S12XDBG module is armed. This bit can be set and cleared by
user software and is automatically cleared on completion of a tracing session, or if a breakpoint is generated with
tracing not enabled. On setting this bit the state sequencer enters State1.
0 Debugger disarmed
1 Debugger armed
Immediate Trigger Request Bit — This bit when written to 1 requests an immediate trigger independent of
comparator signal status. When tracing is complete a forced breakpoint may be generated depending upon
DBGBRK and BDM bit settings. This bit always reads back a 0. Writing a 0 to this bit has no effect. If TSOURCE
is clear no tracing is carried out. If tracing has already commenced using BEGIN- or MID trigger alignment, it
continues until the end of the tracing session as defined by the TALIGN bit settings, thus TRIG has no affect. In
secure mode tracing is disabled and writing to this bit has no effect.
0 Do not trigger until the state sequencer enters the Final State.
1 Trigger immediately .
This bit is reserved, setting it has no meaning or effect.
Background Debug Mode Enable — This bit determines if an S12X breakpoint causes the system to enter
Background Debug Mode (BDM) or initiate a Software Interrupt (SWI). If this bit is set but the BDM is not enabled
by the ENBDM bit in the BDM module, then breakpoints default to SWI.
0 Breakpoint to Software Interrupt if BDM inactive. Otherwise no breakpoint.
1 Breakpoint to BDM, if BDM enabled. Otherwise breakpoint to SWI
Debug Control Register 1 (DBGC1)
0
7
If a write access to DBGC1 with the ARM bit position set occurs
simultaneously to a hardware disarm from an internal trigger event, then the
ARM bit is cleared due to the hardware disarm.
When disarming the S12XDBG by clearing ARM with software, the
contents of bits[5:2] are not affected by the write, since up until the write
operation, ARM = 1 preventing these bits from being written. These bits
must be cleared using a second write if required.
TRIG
0
0
6
Figure 6-3. Debug Control Register (DBGC1)
S12XS Family Reference Manual, Rev. 1.11
Table 6-4. DBGC1 Field Descriptions
reserved
0
5
BDM
NOTE
NOTE
0
4
Description
DBGBRK
0
3
reserved
0
2
Freescale Semiconductor
0
1
COMRV
0
0