S9S12XS256J0CAL Freescale Semiconductor, S9S12XS256J0CAL Datasheet - Page 311

• Manufacturer Part Number: S9S12XS256J0CAL
• Description: MCU 256K FLASH 112-LQFP
• Manufacturer: Freescale Semiconductor
• Series: HCS12r

Specifications of S9S12XS256J0CAL

• Core Processor: HCS12X
• Core Size: 16-Bit
• Speed: 40MHz
• Connectivity: CAN, SCI, SPI
• Peripherals: LVD, POR, PWM, WDT
• Number Of I /o: 91
• Program Memory Size: 256KB (256K x 8)
• Program Memory Type: FLASH
• Eeprom Size: 8K x 8
• Ram Size: 12K x 8
• Voltage - Supply (vcc/vdd): 1.72 V ~ 5.5 V
• Data Converters: A/D 16x12b
• Oscillator Type: External
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 112-LQFP
• Processor Series: S12XS
• Core: HCS12
• Data Bus Width: 16 bit
• Data Ram Size: 12 KB
• Interface Type: CAN, SCI, SPI
• Maximum Clock Frequency: 40 MHz
• Number Of Programmable I/os: 91
• Number Of Timers: 12
• Maximum Operating Temperature: + 85 C
• Mounting Style: SMD/SMT
• 3rd Party Development Tools: EWHCS12
• Development Tools By Supplier: DEMO9S12XSFAME, EVB9S12XEP100
• Minimum Operating Temperature: - 40 C
• On-chip Adc: 12 bit, 16 Channel
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant

1. Read: Anytime
11.3.2.8
This register contains the interrupt enable bits for the transmit buffer empty interrupt flags.
Freescale Semiconductor
Module Base + 0x0006
Module Base + 0x0007
Write: Anytime when not in initialization mode; write of 1 clears flag, write of 0 is ignored
TXE[2:0]
Field
2-0
Reset:
Reset:
W
W
R
R
Transmitter Buffer Empty — This flag indicates that the associated transmit message buffer is empty, and thus
not scheduled for transmission. The CPU must clear the flag after a message is set up in the transmit buffer and
is due for transmission. The MSCAN sets the flag after the message is sent successfully. The flag is also set by
the MSCAN when the transmission request is successfully aborted due to a pending abort request (see
Section 11.3.2.9, “MSCAN Transmitter Message Abort Request Register
transmit interrupt is pending while this flag is set.
Clearing a TXEx flag also clears the corresponding ABTAKx (see
Message Abort Acknowledge Register
is cleared (see
When listen-mode is active (see
cannot be cleared and no transmission is started.
Read and write accesses to the transmit buffer will be blocked, if the corresponding TXEx bit is cleared
(TXEx = 0) and the buffer is scheduled for transmission.
0 The associated message buffer is full (loaded with a message due for transmission)
1 The associated message buffer is empty (not scheduled)
MSCAN Transmitter Interrupt Enable Register (CANTIER)
The CANTFLG register is held in the reset state when the initialization
mode is active (INITRQ = 1 and INITAK = 1). This register is writable when
not in initialization mode (INITRQ = 0 and INITAK = 0).
0
0
0
0
7
7
Figure 11-11. MSCAN Transmitter Interrupt Enable Register (CANTIER)
Figure 11-10. MSCAN Transmitter Flag Register (CANTFLG)
Section 11.3.2.9, “MSCAN Transmitter Message Abort Request Register
= Unimplemented
= Unimplemented
Table 11-13. CANTFLG Register Field Descriptions
6
0
0
6
0
0
S12XS Family Reference Manual Rev. 1.11
Section 11.3.2.2, “MSCAN Control Register 1
0
0
0
0
5
5
(CANTAAK)”). When a TXEx flag is set, the corresponding ABTRQx bit
NOTE
4
0
0
4
0
0
Description
Freescale’s Scalable Controller Area Network (S12MSCANV3)
0
0
0
0
3
3
Section 11.3.2.10, “MSCAN Transmitter
TXEIE2
(CANTARQ)”). If not masked, a
TXE2
2
1
2
0
(CANCTL1)”) the TXEx flags
Access: User read/write
Access: User read/write
TXEIE1
TXE1
(CANTARQ)”).
1
0
1
1
TXEIE0
TXE0
0
1
0
0
311
(1)
(1)