MC908AZ32ACFU Freescale Semiconductor, MC908AZ32ACFU Datasheet - Page 104

• Manufacturer Part Number: MC908AZ32ACFU
• Description: IC MCU 32K FLASH 8.4MHZ 64-QFP
• Manufacturer: Freescale Semiconductor
• Series: HC08r

Specifications of MC908AZ32ACFU

• Core Processor: HC08
• Core Size: 8-Bit
• Speed: 8MHz
• Connectivity: CAN, SCI, SPI
• Peripherals: LVD, POR, PWM
• Number Of I /o: 40
• Program Memory Size: 32KB (32K x 8)
• Program Memory Type: FLASH
• Eeprom Size: 512 x 8
• Ram Size: 1K x 8
• Voltage - Supply (vcc/vdd): 4.5 V ~ 5.5 V
• Data Converters: A/D 15x8b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 64-QFP
• Lead Free Status / RoHS Status: Contains lead / RoHS non-compliant

Clock Generator Module (CGM)
8.9 Acquisition/Lock Time Specifications
The acquisition and lock times of the PLL are, in many applications, the most critical PLL design
parameters. Proper design and use of the PLL ensures the highest stability and lowest acquisition/lock
times.
8.9.1 Acquisition/Lock Time Definitions
Typical control systems refer to the acquisition time or lock time as the reaction time, within specified
tolerances, of the system to a step input. In a PLL, the step input occurs when the PLL is turned on or
when it suffers a noise hit. The tolerance is usually specified as a percent of the step input or when the
output settles to the desired value plus or minus a percent of the frequency change. Therefore, the
reaction time is constant in this definition, regardless of the size of the step input. For example, consider
a system with a 5% acquisition time tolerance. If a command instructs the system to change from 0 Hz to
1 MHz, the acquisition time is the time taken for the frequency to reach 1 MHz ±50 kHz. Fifty kHz = 5%
of the 1-MHz step input. If the system is operating at 1 MHz and suffers a –100 kHz noise hit, the
acquisition time is the time taken to return from 900 kHz to 1 MHz ±5 kHz. Five kHz = 5% of the 100-kHz
step input.
Other systems refer to acquisition and lock times as the time the system takes to reduce the error between
the actual output and the desired output to within specified tolerances. Therefore, the acquisition or lock
time varies according to the original error in the output. Minor errors may not even be registered. Typical
PLL applications prefer to use this definition because the system requires the output frequency to be
within a certain tolerance of the desired frequency regardless of the size of the initial error.
The discrepancy in these definitions makes it difficult to specify an acquisition or lock time for a typical
PLL. Therefore, the definitions for acquisition and lock times for this module are:
Obviously, the acquisition and lock times can vary according to how large the frequency error is and may
be shorter or longer in many cases.
104
•
•
Acquisition time, t
frequency and the desired output frequency to less than the tracking mode entry tolerance, Δ
Acquisition time is based on an initial frequency error, (f
automatic bandwidth control mode (see
acquisition time expires when the ACQ bit becomes set in the PLL bandwidth control register
(PBWC).
Lock time, t
and the desired output frequency to less than the lock mode entry tolerance, Δ
based on an initial frequency error, (f
bandwidth control mode, lock time expires when the LOCK bit becomes set in the PLL bandwidth
control register (PBWC). (See
Lock
, is the time the PLL takes to reduce the error between the actual output frequency
acq
, is the time the PLL takes to reduce the error between the actual output
MC68HC908AZ32A Data Sheet, Rev. 2
8.3.2.3 Manual and Automatic PLL Bandwidth
des
8.3.2.3 Manual and Automatic PLL Bandwidth
– f
orig
)/f
des
, of not more than ±100%. In automatic
des
– f
orig
)/f
des
, of not more than ±100%. In
Freescale Semiconductor
Modes).
Lock
. Lock time is
Modes),
trk
.