M30262F8GP#U7 Renesas Electronics America, M30262F8GP#U7 Datasheet - Page 171

• Manufacturer Part Number: M30262F8GP#U7
• Description: IC M16C/TINY MCU FLASH 48LQFP
• Manufacturer: Renesas Electronics America
• Series: M16C™ M16C/Tiny/26r

Specifications of M30262F8GP#U7

• Core Processor: M16C/60
• Core Size: 16-Bit
• Speed: 20MHz
• Connectivity: I²C, IEBus, SIO, UART/USART
• Peripherals: DMA, WDT
• Number Of I /o: 38
• Program Memory Size: 64KB (64K x 8)
• Program Memory Type: FLASH
• Ram Size: 2K x 8
• Voltage - Supply (vcc/vdd): 2.7 V ~ 5.5 V
• Data Converters: A/D 8x10b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 48-LQFP
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Eeprom Size: -

Programmable I/O Ports
Programmable I/O Ports
There are 38 programmable I/O ports: P1
can be set independently for input or output using the direction register. A pull-up resistance for each block
of 4 ports can be set.
Figures 1.17.1 to 1.17.3 show the programmable I/O ports. Figure 1.17.4 shows the I/O pins.
Each pin functions as a programmable I/O port and as the I/O for the built-in peripheral devices.
To use the pins as the inputs for the built-in peripheral devices, set the direction register of each pin to input
mode. When the pins are used as the outputs for the built-in peripheral devices, they function as outputs
regardless of the contents of the direction registers. See the descriptions of the respective functions for
how to set up the built-in peripheral devices.
(1) Direction registers
(2) Port registers
(3) Pull-up control registers
(4) Port control register
Figure 1.17.5 shows the port direction registers.
These registers are used to choose the direction of the programmable I/O ports. Each bit in these
registers corresponds one for one to each I/O pin.
Note: The Port 9 direction register incorporates a write protection function. Before writing to the port 9
direction register the write protection must be disabled by setting PRC2 of the Protect register (bit 2 at
000A
Figure 1.17.6 shows the port registers.
These registers are used to read and write data for input and output to and from an external device. A
port register consists of a port latch to hold output data and a circuit to read the status of a pin. Each bit
in the port registers corresponds one for one to each I/O pin.
Figure 1.17.7 shows the pull-up control registers.
The pull-up control register can be set to apply a pull-up resistance to each block of 4 ports. When ports
are set to have a pull-up resistance, the pull-up resistance is connected only when the direction register
is set to input.
Figure 1.17.8 shows the port control register.
Bit 0 of the port control register is used to control the read of port P1 as follows:
0 : When port P1 is set as an input port, the port input level is read.
1 : The contents of the port P1 register are always read.
16
When port P1 is set as an output port , the contents of the port P1 register are read.
) to "1". Note that PRC2 is automatically reset to "0" after the next write to an SFR address.
Preliminary Specifications Rev. 0.9
Specifications in this manual are tentative and subject to change.
Renesas Technology Corp.
5
- P1
7
, P6, P7, P8 (except P8
SINGLE-CHIP 16-BIT CMOS MICROCOMPUTER
4
), P9
0
- P9
3
, and P10. Each port
M16C/26 Group
163