M30262F8GP#U7 Renesas Electronics America, M30262F8GP#U7 Datasheet - Page 75

• Manufacturer Part Number: M30262F8GP#U7
• Description: IC M16C/TINY MCU FLASH 48LQFP
• Manufacturer: Renesas Electronics America
• Series: M16C™ M16C/Tiny/26r

Specifications of M30262F8GP#U7

• Core Processor: M16C/60
• Core Size: 16-Bit
• Speed: 20MHz
• Connectivity: I²C, IEBus, SIO, UART/USART
• Peripherals: DMA, WDT
• Number Of I /o: 38
• Program Memory Size: 64KB (64K x 8)
• Program Memory Type: FLASH
• Ram Size: 2K x 8
• Voltage - Supply (vcc/vdd): 2.7 V ~ 5.5 V
• Data Converters: A/D 8x10b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 48-LQFP
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Eeprom Size: -

DMAC
Table 1.11.1. DMAC specifications
Note: DMA transfer is not effective to any interrupt. DMA transfer is affected neither by the interrupt enable
No. of channels
Transfer memory space
cessed)
Maximum No. of bytes transferred 128K bytes (with 16-bit transfers) or 64K bytes (with 8-bit transfers)
DMA request factors (Note)
Channel priority
Transfer unit
Transfer address direction
Transfer mode
DMA interrupt request
generation timing
Active
Writing to register
Reading the register
Inactive
flag (I flag) nor by the interrupt priority level.
Preliminary Specifications Rev. 0.9
Specifications in this manual are tentative and subject to change.
Item
2 (cycle steal method)
• From any address in the 1M bytes space to a fixed address
• From a fixed address to any address in the 1M bytes space
• From a fixed address to a fixed address
Falling edge of INT0 or INT1 or both edge
Timer A0 to timer A4 interrupt requests
Timer B0 to timer B2 interrupt requests
UART0 transfer and reception interrupt requests
UART1 transfer and reception interrupt requests
UART2 transfer and reception interrupt requests
A-D conversion interrupt requests
Software triggers
DMA0 takes precedence if DMA0 and DMA1 requests are
generated simultaneously
8 bits or 16 bits
forward/fixed (forward direction cannot be specified for both source and
• Single transfer mode
After the transfer counter underflows, the DMA enable bit turns to “0”,
and the DMAC turns inactive
• Repeat transfer mode
After the transfer counter underflows, the value of the transfer counter
reload register is reloaded to the transfer counter.
The DMAC remains active unless a “0” is written to the DMA enable bit.
When an underflow occurs in the transfer counter
When the DMA enable bit is set to “1”, the DMAC is active.
When the DMAC is active, data transfer starts every time a DMA
transfer request signal occurs.
• When the DMA enable bit is set to “0”, the DMAC is inactive.
• After the transfer counter underflows in single transfer mode
At the time of starting data transfer immediately after turning the DMAC
active, the value of one of source pointer and destination pointer - the one
specified for the forward direction- is reloaded to the forward direction
address pointer, and the value of the transfer counter reload register is
reloaded to the transfer counter.
Registers specified for forward direction transfer are always write enabled.
Registers specified for fixed address transfer are write-enabled when
the DMA enable bit is “0”.
Can be read at any time.
However, when the DMA enable bit is “1”, reading the register set up as the
forward register is the same as reading the value of the forward address pointer.
(Note that DMA-related registers [0020
destination simultaneously)
Renesas Technology Corp.
Specification
SINGLE-CHIP 16-BIT CMOS MICROCOMPUTER
16
to 003F
M16C/26 Group
16
] cannot be ac-
67