ST7LITE49K2 STMicroelectronics, ST7LITE49K2 Datasheet - Page 32
ST7LITE49K2
Manufacturer Part Number
ST7LITE49K2
Description
8-bit MCU
Manufacturer
STMicroelectronics
Datasheet
1.ST7LITE49K2.pdf
(245 pages)
Specifications of ST7LITE49K2
8 Kbytes Single Voltage Extended Flash (xflash) Program Memory With Read-out Protection In-circuit Programming And In-application Programming (icp And Iap) Endurance
10K write/erase cycles guaranteed Data retention
256 Bytes Data Eeprom With Read-out Protection. 300k Write/erase Cycles Guaranteed, Data Retention
20 years at 55 °C.
Clock Sources
Internal trimmable 8 MHz RC oscillator, auto-wakeup internal low power - low frequency oscillator, crystal/ceramic resonator or external clock
Five Power Saving Modes
Halt, Active-halt, Auto-wakeup from Halt, Wait and Slow
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
- Current page: 32 of 245
- Download datasheet (4Mb)
Data EEPROM
5.6
Note:
5.7
Note:
32/245
Data EEPROM read-out protection
The read-out protection is enabled through an option bit (see
When this option is selected, the programs and data stored in the EEPROM memory are
protected against Read-out (including a re-write protection). In Flash devices, when this
protection is removed by reprogramming the option byte, the entire Program memory and
EEPROM is first automatically erased.
Both Program Memory and data EEPROM are protected using the same option bit.
Figure 9.
EEPROM control/status register (EECSR)
Address: 0035h
Reset value: 0000 0000 (00h)
Bits 7:2 = Reserved, forced by hardware to 0
Bit 1 = E2LAT Latch access transfer bit: this bit is set by software.
Bit 0 = E2PGM Programming control and status bit
If the E2PGM bit is cleared during the programming cycle, the memory data is not
guaranteed.
Internal
Programming
voltage
0: Read mode
1: Write mode
It is cleared by hardware at the end of the programming cycle. It can only be cleared by
software if the E2PGM bit is cleared
This bit is set by software to begin the programming cycle. At the end of the
programming cycle, this bit is cleared by hardware.
0: Programming finished or not yet started
1: Programming cycle is in progress
7
0
Data EEPROM programming cycle
DATA LATCHES
WRITE OF
0
READ OPERATION NOT POSSIBLE
0
ERASE CYCLE
0
t
Read/write
PROG
WRITE CYCLE
0
Section 14.1: Option
0
READ OPERATION POSSIBLE
E2LAT
LAT
PGM
ST7LITE49K2
E2PGM
bytes).
0
Related parts for ST7LITE49K2
Image
Part Number
Description
Manufacturer
Datasheet
Request
R
Part Number:
Description:
STMicroelectronics [RIPPLE-CARRY BINARY COUNTER/DIVIDERS]
Manufacturer:
STMicroelectronics
Datasheet:
Part Number:
Description:
STMicroelectronics [LIQUID-CRYSTAL DISPLAY DRIVERS]
Manufacturer:
STMicroelectronics
Datasheet:
Part Number:
Description:
BOARD EVAL FOR MEMS SENSORS
Manufacturer:
STMicroelectronics
Datasheet:
Part Number:
Description:
NPN TRANSISTOR POWER MODULE
Manufacturer:
STMicroelectronics
Datasheet:
Part Number:
Description:
TURBOSWITCH ULTRA-FAST HIGH VOLTAGE DIODE
Manufacturer:
STMicroelectronics
Datasheet:
Part Number:
Description:
Manufacturer:
STMicroelectronics
Datasheet:
Part Number:
Description:
DIODE / SCR MODULE
Manufacturer:
STMicroelectronics
Datasheet:
Part Number:
Description:
DIODE / SCR MODULE
Manufacturer:
STMicroelectronics
Datasheet:
Part Number:
Description:
Search -----> STE16N100
Manufacturer:
STMicroelectronics
Datasheet:
Part Number:
Description:
Search ---> STE53NA50
Manufacturer:
STMicroelectronics
Datasheet:
Part Number:
Description:
NPN Transistor Power Module
Manufacturer:
STMicroelectronics
Datasheet:
Part Number:
Description:
DIODE / SCR MODULE
Manufacturer:
STMicroelectronics
Datasheet: