AT32AP7002-CTUT Atmel, AT32AP7002-CTUT Datasheet - Page 404

• Manufacturer Part Number: AT32AP7002-CTUT
• Description: IC MCU 32BIT AVR32 196-CBGA
• Manufacturer: Atmel
• Series: AVR®32 AP7r

Specifications of AT32AP7002-CTUT

• Core Processor: AVR
• Core Size: 32-Bit
• Speed: 150MHz
• Connectivity: EBI/EMI, I²C, MMC, PS2, SPI, SSC, UART/USART, USB
• Peripherals: AC'97, DMA, I²C, LCD, POR, PWM, WDT
• Number Of I /o: 85
• Program Memory Type: ROMless
• Ram Size: 32K x 8
• Voltage - Supply (vcc/vdd): 1.65 V ~ 1.95 V
• Data Converters: D/A 2x16b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 196-CBGA
• Data Bus Width: 32 bit
• Data Ram Size: 32 KB
• Interface Type: I2C, JTAG, PS2, SPI, SSC, UART, USART, USB
• Maximum Clock Frequency: 150 MHz
• Number Of Timers: 3
• Maximum Operating Temperature: + 85 C
• Mounting Style: SMD/SMT
• Minimum Operating Temperature: - 40 C
• On-chip Dac: 16 bit, 2 Channel
• Package: 196CTBGA
• Device Core: AVR32
• Family Name: AT32
• Maximum Speed: 150 MHz
• Operating Supply Voltage: 1.8|3.3 V
• For Use With: ATAVRONEKIT - KIT AVR/AVR32 DEBUGGER/PROGRMMRATNGW100 - KIT AVR32 NETWORK GATEWAYATSTK1000 - KIT STARTER FOR AVR32AP7000
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Eeprom Size: -
• Program Memory Size: -
• Lead Free Status / Rohs Status: Details

Figure 24-22. Parity Error
24.7.3.10
24.7.3.11
32054F–AVR32–09/09
Multidrop Mode
Transmitter Timeguard
Baud Rate
If the PAR field in the Mode Register (MR) is programmed to the value 0x6 or 0x07, the USART
runs in Multidrop Mode. This mode differentiates the data characters and the address charac-
ters. Data is transmitted with the parity bit at 0 and addresses are transmitted with the parity bit
at 1.
If the USART is configured in multidrop mode, the receiver sets the PARE parity error bit when
the parity bit is high and the transmitter is able to send a character with the parity bit high when
the Control Register is written with the SENDA bit at 1.
To handle parity error, the PARE bit is cleared when the Control Register is written with the bit
RSTSTA at 1.
The transmitter sends an address byte (parity bit set) when SENDA is written to CR. In this case,
the next byte written to THR is transmitted as an address. Any character written in THR without
having written the command SENDA is transmitted normally with the parity at 0.
The timeguard feature enables the USART interface with slow remote devices.
The timeguard function enables the transmitter to insert an idle state on the TXD line between
two characters. This idle state actually acts as a long stop bit.
The duration of the idle state is programmed in the TG field of the Transmitter Timeguard Regis-
ter (TTGR). When this field is programmed at zero no timeguard is generated. Otherwise, the
transmitter holds a high level on TXD after each transmitted byte during the number of bit peri-
ods programmed in TG in addition to the number of stop bits.
As illustrated in
the programming of a timeguard. TXRDY rises only when the start bit of the next character is
sent, and thus remains at 0 during the timeguard transmission if a character has been written in
THR. TXEMPTY remains low until the timeguard transmission is completed as the timeguard is
part of the current character being transmitted.
RXRDY
US_CR
PARE
Clock
Write
RXD
Start
Bit
D0
Figure
D1
D2
24-23, the behavior of TXRDY and TXEMPTY status bits is modified by
D3
D4
D5
D6
D7
Parity
Bad
Bit
Stop
Bit
RSTSTA = 1
AT32AP7002
404