ATMEGA128A-AU Atmel, ATMEGA128A-AU Datasheet - Page 106

• Manufacturer Part Number: ATMEGA128A-AU
• Description: MCU 8BIT 128K ISP FLASH 64-TQFP
• Manufacturer: Atmel
• Series: AVR® ATmegar

Specifications of ATMEGA128A-AU

• Core Processor: AVR
• Core Size: 8-Bit
• Speed: 16MHz
• Connectivity: EBI/EMI, I²C, SPI, UART/USART
• Peripherals: Brown-out Detect/Reset, POR, PWM, WDT
• Number Of I /o: 53
• Program Memory Size: 128KB (64K x 16)
• Program Memory Type: FLASH
• Eeprom Size: 4K x 8
• Ram Size: 4K x 8
• Voltage - Supply (vcc/vdd): 2.7 V ~ 5.5 V
• Data Converters: A/D 8x10b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 64-TQFP, 64-VQFP
• Processor Series: ATMEGA128x
• Core: AVR8
• Data Bus Width: 8 bit
• Data Ram Size: 4 KB
• Interface Type: JTAG
• Maximum Clock Frequency: 16 MHz
• Number Of Programmable I/os: 53
• Number Of Timers: 4
• Operating Supply Voltage: 2.7 V to 5.5 V
• Maximum Operating Temperature: + 85 C
• Mounting Style: SMD/SMT
• 3rd Party Development Tools: EWAVR, EWAVR-BL
• Development Tools By Supplier: ATAVRDRAGON, ATSTK500, ATSTK600, ATAVRISP2, ATAVRONEKIT
• Minimum Operating Temperature: - 40 C
• On-chip Adc: 10 bit, 8 Channel
• On-chip Dac: 10 bit, 8 Channel
• Cpu Family: ATmega
• Device Core: AVR
• Device Core Size: 8b
• Frequency (max): 16MHz
• Total Internal Ram Size: 4KB
• # I/os (max): 53
• Number Of Timers - General Purpose: 4
• Operating Supply Voltage (typ): 3.3/5V
• Operating Supply Voltage (max): 5.5V
• Operating Supply Voltage (min): 2.7V
• Instruction Set Architecture: RISC
• Operating Temp Range: -40C to 85C
• Operating Temperature Classification: Industrial
• Mounting: Surface Mount
• Pin Count: 64
• Package Type: TQFP
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Other names: Q4784435

14.10 Timer/Counter Prescaler
14.11 Register Description
14.11.1
8151H–AVR–02/11
TCCR0 - Timer/Counter Control Register
Figure 14-12. Prescaler for Timer/Counter0
The clock source for Timer/Counter0 is named clk
system clock clk
from the TOSC1 pin. This enables use of Timer/Counter0 as a Real Time Counter (RTC). When
AS0 is set, pins TOSC1 and TOSC2 are disconnected from Port C. A crystal can then be con-
nected between the TOSC1 and TOSC2 pins to serve as an independent clock source for
Timer/Counter0. The Oscillator is optimized for use with a 32.768kHz crystal. Applying an exter-
nal clock source to TOSC1 is not recommended.
For Timer/Counter0, the possible prescaled selections are: clk
clk
Setting the PSR0 bit in SFIOR resets the prescaler. This allows the user to operate with a pre-
dictable prescaler.
• Bit 7 – FOC0: Force Output Compare
The FOC0 bit is only active when the WGM bits specify a non-PWM mode. However, for ensur-
ing compatibility with future devices, this bit must be set to zero when TCCR0 is written when
operating in PWM mode. When writing a logical one to the FOC0 bit, an immediate compare
match is forced on the waveform generation unit. The OC0 output is changed according to its
Bit
Read/Write
Initial Value
T0S
TOSC1
/128, clk
clk
PSR0
CS00
CS01
CS02
AS0
I/O
T0S
FOC0
I/O
/256, and clk
W
7
0
. By setting the AS0 bit in ASSR, Timer/Counter0 is asynchronously clocked
WGM00
R/W
6
0
clk
T0S
T0S
/1024. Additionally, clk
COM01
R/W
5
0
Clear
COM00
R/W
TIMER/COUNTER0 CLOCK SOURCE
4
0
0
T0
WGM01
R/W
. clk
3
0
10-BIT T/C PRESCALER
T0S
T0
clk
as well as 0 (stop) may be selected.
T0
is by default connected to the main
CS02
R/W
2
0
T0S
CS01
ATmega128A
R/W
/8, clk
1
0
T0S
CS00
R/W
/32, clk
0
0
TCCR0
T0S
/64,
106