ATSAM3U4CA-CU Atmel, ATSAM3U4CA-CU Datasheet - Page 815

IC MCU 32BIT 256KB FLSH 100TFBGA

ATSAM3U4CA-CU

Manufacturer Part Number
ATSAM3U4CA-CU
Description
IC MCU 32BIT 256KB FLSH 100TFBGA
Manufacturer
Atmel
Series
SAM3Ur
Datasheets

Specifications of ATSAM3U4CA-CU

Core Processor
ARM® Cortex-M3™
Core Size
32-Bit
Speed
96MHz
Connectivity
EBI/EMI, I²C, MMC, SPI, SSC, UART/USART, USB
Peripherals
Brown-out Detect/Reset, DMA, I²S, POR, PWM, WDT
Number Of I /o
57
Program Memory Size
256KB (256K x 8)
Program Memory Type
FLASH
Ram Size
52K x 8
Voltage - Supply (vcc/vdd)
1.65 V ~ 1.95 V
Data Converters
A/D 4x10b, 4x12b
Oscillator Type
Internal
Operating Temperature
-40°C ~ 85°C
Package / Case
100-TFBGA
Processor Series
ATSAM3x
Core
ARM Cortex M3
Data Bus Width
32 bit
Data Ram Size
52 KB
Interface Type
3xUSART, TWI, 4xSPI, Bus
Maximum Clock Frequency
96 MHz
Number Of Programmable I/os
57
Number Of Timers
8
Operating Supply Voltage
1.62 V to 3.6 V
Maximum Operating Temperature
+ 85 C
Mounting Style
SMD/SMT
3rd Party Development Tools
JTRACE-CM3, MDK-ARM, RL-ARM, ULINK2
Development Tools By Supplier
ATSAM3U-EK
Minimum Operating Temperature
- 40 C
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
Eeprom Size
-
Lead Free Status / Rohs Status
Lead free / RoHS Compliant

Available stocks

Company
Part Number
Manufacturer
Quantity
Price
Part Number:
ATSAM3U4CA-CU
Manufacturer:
Atmel
Quantity:
10 000
Part Number:
ATSAM3U4CA-CU
Manufacturer:
ATMEL/爱特梅尔
Quantity:
20 000
37.7.5
6430D–ATARM–25-Mar-11
WRITE_SINGLE_BLOCK Operation using DMA Controller
1. Wait until the current command execution has successfully terminated.
2. Program the block length in the card. This value defines the value block_length.
3. Program the block length in the HSMCI configuration register with block_length value.
4. Program HSMCI_DMA register with the following fields:
5. Issue a WRITE_SINGLE_BLOCK command writing HSMCI_ARG then HSMCI_CMDR.
6. Program the DMA Controller.
c. Check that CMDRDY and NOTBUSY fields are asserted in HSMCI_SR
– OFFSET field with dma_offset.
– CHKSIZE is user defined and set according to DMAC_DCSIZE.
– DMAEN is set to true to enable DMA hardware handshaking in the HSMCI. This bit
a. Read the channel Register to choose an available (disabled) channel.
b. Clear any pending interrupts on the channel from the previous DMAC transfer by
c. Program the channel registers.
d. The DMAC_SADDRx register for channel x must be set to the location of the
e. The DMAC_DADDRx register for channel x must be set with the starting address of
f.
g. Program DMAC_CTRLBx register for channel x with the following field’s values:
h. Program DMAC_CFGx register for channel x with the following field’s values:
was previously set to false.
reading the DMAC_EBCISR register.
source data. When the first data location is not word aligned, the two LSB bits
define the temporary value called dma_offset. The two LSB bits of
DMAC_SADDRx must be set to 0.
the HSMCI_FIFO address.
Program DMAC_CTRLAx register of channel x with the following field’s values:
–DST_WIDTH is set to WORD.
–SRC_WIDTH is set to WORD.
–DCSIZE must be set according to the value of HSMCI_DMA, CHKSIZE field.
–BTSIZE is programmed with CEILING((block_length + dma_offset) / 4), where
–DST_INCR is set to INCR, the block_length value must not be larger than the
–SRC_INCR is set to INCR.
–FC field is programmed with memory to peripheral flow control mode.
–both DST_DSCR and SRC_DSCR are set to 1 (descriptor fetch is disabled).
–DIF and SIF are set with their respective layer ID. If SIF is different from DIF, the
–FIFOCFG defines the watermark of the DMAC channel FIFO.
–DST_H2SEL is set to true to enable hardware handshaking on the destination.
–DST_PER is programmed with the hardware handshaking ID of the targeted
the ceiling function is the function that returns the smallest integer not less than
x.
HSMCI_FIFO aperture.
DMA controller is able to prefetch data and write HSMCI simultaneously.
HSMCI Host Controller.
SAM3U Series
815

Related parts for ATSAM3U4CA-CU