XW2Z-070T-1 Omron, XW2Z-070T-1 Datasheet - Page 149

no-image

XW2Z-070T-1

Manufacturer Part Number
XW2Z-070T-1
Description
Special Nissan
Manufacturer
Omron
Series
XW2Zr
Type
DB09r
Datasheet

Specifications of XW2Z-070T-1

1st Connector
Plug, Male Pins
2nd Connector
Plug, Male Pins
Number Of Positions
9
Length
2.3' (701.0mm)
Color
Beige, Individual (Round)
Usage
Communication
Contact Finish
Gold
Contact Finish Thickness
15µin (0.38µm)
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
Shielding
-
Lead Free Status / Rohs Status
Lead free / RoHS Compliant
Other names
XW2Z070T1
9-1
9-1-1
Clearing Memory
Operating Mode at Startup
9-1-2
9-2
138
Initial System Checks and Test Run Procedure
Initial System Checks and Test Run Procedure
CPM2B-S Test Run Procedure
Flash Memory Precautions
Initial System Checks
1,2,3...
1,2,3...
Check the following items after setting up and wiring the CPM2B-S, but before
performing a test run.
Always clear memory before beginning to program the CPM2B-S. Although
memory is cleared before the CPU Board is shipped, the contents of the DM,
HR, AR, and counter areas may change in transit.
See 1-3-3 Operating Mode at Startup to determine what mode the CPM2B-S
will enter when the power is turned on.
Observe the following precautions to protect the flash memory and ensure
proper operation.
1. If changes are made in the read-only DM area (DM 6144 through DM
2. When contents of the program, read-only DM (DM 6144 through DM
3. If one of the following three operations is performed in MONITOR or RUN
1. Power Supply Application
Power supply and
I/O connections
Connecting cables Are the cables all connected correctly and locked?
6599) or PC Setup (DM 6600 through DM 6655), the PC’s operating mode
must be changed to write the new contents to flash memory. If backup bat-
tery is replaced before the changes are written to flash memory, the chang-
es will be lost.
The changes can be saved by switching the CPM2B-S to RUN or MONI-
TOR mode or turning the CPM2B-S OFF and then ON again.
6599), or PC Setup (DM 6600 through DM 6655) have been changed, star-
tup processing will take up to 1,200 ms longer than usual. Be sure to take
this one-time startup delay into account if it may affect operations.
mode, the CPM2B-S’s cycle time will be extended by up to 1,200 ms and
interrupts will be disabled while the program or PC Setup is being overwrit-
ten.
A “SCAN TIME OVER” error won’t occur during these operations. Be sure
to take this delay in the CPM2B-S’s I/O response times into account when
performing online editing.
a) Check the CPM2B-S’s power supply voltage and terminal connec-
b) Check the I/O devices’ power supply voltage and terminal connec-
c) Turn on the power supply and check that the “PWR” indicator lights.
d) Use a Programming Device to set the CPM2B-S to PROGRAM mode.
• Program changes with the online edit operation
• Changes to the read-only DM area (DM 6144 through DM 6599)
• Changes to the PC Setup (DM 6600 through DM 6655)
Item
tions.
tions.
Is the wiring correct?
Are the terminals securely tightened?
Are there any shorts between crimp terminals or wires?
Refer to 3-5 Wiring and Connections for details.
Refer to 3-5 Wiring and Connections for details.
Points to check
Section 9-1

Related parts for XW2Z-070T-1