XW2Z-070T-1 Omron, XW2Z-070T-1 Datasheet - Page 37

• Manufacturer Part Number: XW2Z-070T-1
• Description: Special Nissan
• Manufacturer: Omron
• Series: XW2Zr
• Type: DB09r

Specifications of XW2Z-070T-1

• 1st Connector: Plug, Male Pins
• 2nd Connector: Plug, Male Pins
• Number Of Positions: 9
• Length: 2.3' (701.0mm)
• Color: Beige, Individual (Round)
• Usage: Communication
• Contact Finish: Gold
• Contact Finish Thickness: 15µin (0.38µm)
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Shielding: -
• Lead Free Status / Rohs Status: Lead free / RoHS Compliant
• Other names: XW2Z070T1

Pulse output
Synchronized pulse control
Quick-response inputs
Input time constant
(ON response time = OFF response
time)
Communications functions
Memory protection
(See notes 1 and 2.)
Memory backup
(See notes 1 and 2.)
Self-diagnostic functions
Program checks
24
Specifications
Item
Note
1. The DM area, HR area, AR area, and counter values are backed up by the
2. The contents of the program area, read-only DM area (DM 6144 to
2 points with no acceleration/deceleration, 10 Hz to 10 kHz each, and no direction
control.
1 point with trapezoidal acceleration/deceleration, 10 Hz to 10 kHz, and direction
control.
2 points with variable duty-ratio outputs.
(Pulse outputs can be used with transistor outputs only, they cannot be used with
relay outputs.)
1 point:
A pulse output can be created by combining the high-speed counter with pulse
outputs and multiplying the frequency of the input pulses from the high-speed
counter by a fixed factor.
(This output is possible with transistor outputs only, it cannot be used with relay
outputs.)
2 points (Min. input pulse width: 50 µs max.) (Also used for interrupt inputs and for
interrupt inputs in counter mode.)
Can be set for all input points except those for IR 001 and IR 002.
(1 ms, 2 ms, 3 ms, 5 ms, 10 ms, 20 ms, 40 ms, or 80 ms)
Built-in peripheral port:
Supports Host Link, peripheral bus, no-protocol, or Programming Console
connections.
Built-in RS-232C port:
Supports Host Link, no-protocol, 1:1 PC Link (Master/Slave), or 1:1 NT Link
connections.
(RS-232C communications are available only in CPU Boards equipped with an
RS-232C port.)
HR area, AR area, program contents, read/write DM area contents, and counter val-
ues maintained during power interruptions.
Flash memory:
Program, read-only DM area, and PC Setup
Battery or capacitor backup:
The read/write DM area, HR area, AR area, and counter values are backed up by a
battery.
• Backup time without a battery (optional) is approximately 10 days at 25°C.
• Backup time with a battery (optional) connected is approximately 5 years at
CPU error (watchdog timer), I/O bus error, battery error, and memory error
No END instruction, programming errors (checked when operation is started)
battery or capacitor on the CPU Board. If the battery or capacitor is dis-
charged, the contents of these areas will be lost and the data values will
revert to the defaults.
DM 6599), and PC Setup (DM 6600 to DM 6655) are stored in flash mem-
ory. The contents of these areas will be read from flash memory the next
time the power is turned ON, even if the backup battery or capacitor is dis-
charged.
When data has been changed in any of these areas, write the new values
to flash memory by switching the CPM2B-S to MONITOR or RUN mode,
or by turning the power OFF and then ON again.
25°C.
CPU Boards
Section 2-1