MPC8379EVRAJF Freescale Semiconductor, MPC8379EVRAJF Datasheet - Page 107

• Manufacturer Part Number: MPC8379EVRAJF
• Description: MPU PWRQUICC II 533MHZ 689TEPBGA
• Manufacturer: Freescale Semiconductor
• Series: PowerQUICC II PROr

Specifications of MPC8379EVRAJF

• Processor Type: MPC83xx PowerQUICC II Pro 32-Bit
• Speed: 533MHz
• Voltage: 1V
• Mounting Type: Surface Mount
• Package / Case: 689-TePBGA II
• Maximum Clock Frequency: 533 MHz
• Operating Supply Voltage: 1.8 V to 2.5 V
• Maximum Operating Temperature: + 105 C
• Mounting Style: SMD/SMT
• I/o Voltage: 1.8 V, 2.5 V, 3.3 V
• Minimum Operating Temperature: 0 C
• Core Size: 32 Bit
• Program Memory Size: 64KB
• Cpu Speed: 533MHz
• Embedded Interface Type: DUART, HSSI, I2C, IPIC, JTAG, SPI, USB
• Digital Ic Case Style: BGA
• No. Of Pins: 689
• Rohs Compliant: Yes
• For Use With: MPC8377E-RDBA - BOARD REF DES MPC8377 REV 2.1MPC8377E-MDS-PB - BOARD MODULAR DEV SYSTEM
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Features: -
• Lead Free Status / Rohs Status: Lead free / RoHS Compliant

As shown in
loop (PLL) and the clock unit to create the coherent system bus clock (csb_clk), the internal clock for the
DDR controller (ddr_clk), and the internal clock for the local bus interface unit (lbiu_clk).
The csb_clk frequency is derived from a complex set of factors that can be simplified into the following
equation:
In PCI host mode, PCI_SYNC_IN × (1 + CFG_CLKIN_DIV) is the CLKIN frequency.
The csb_clk serves as the clock input to the e300 core. A second PLL inside the e300 core multiplies up
the csb_clk frequency to create the internal clock for the e300 core (core_clk). The system and core PLL
multipliers are selected by the SPMF and COREPLL fields in the reset configuration word low register
(RCWLR) which is loaded at power-on reset or by one of the hard-coded reset options. See Chapter 4,
“Reset, Clocking, and Initialization,” in the MPC8379E Reference Manual for more information on the
clock subsystem.
The internal ddr_clk frequency is determined by the following equation:
Note that ddr_clk is not the external memory bus frequency; ddr_clk passes through the DDR clock divider
(÷2) to create the differential DDR memory bus clock outputs (MCK and MCK). However, the data rate
is the same frequency as ddr_clk.
The internal lbiu_clk frequency is determined by the following equation:
Note that lbiu_clk is not the external local bus frequency; lbiu_clk passes through the LBIU clock divider
to create the external local bus clock outputs (LCLK[0:2]). The eLBC clock divider ratio is controlled by
LCRR[CLKDIV].
Some of the internal units may be required to be shut off or operate at lower frequency than the csb_clk
frequency. Those units have a default clock ratio that can be configured by a memory mapped register after
the device comes out of reset.
Freescale Semiconductor
eTSEC1, eTSEC2
eSDHC and I
Security block
USB DR
PCI and DMA complex
2
C1
Figure
Unit
1
MPC8377E PowerQUICC II Pro Processor Hardware Specifications, Rev. 4
csb_clk = {PCI_SYNC_IN × (1 + CFG_CLKIN_DIV)} × SPMF
64, the primary clock input (frequency) is multiplied up by the system phase-locked
ddr_clk = csb_clk × (1 + RCWLR[DDRCM])
lbiu_clk = csb_clk × (1 + RCWLR[LBCM])
Table 73
Table 73. Configurable Clock Units
Default Frequency
specifies which units have a configurable clock frequency.
csb_clk/3
csb_clk/3
csb_clk/3
csb_clk/3
csb_clk
Off, csb_clk, csb_clk/2, csb_clk/3
Off, csb_clk, csb_clk/2, csb_clk/3
Off, csb_clk, csb_clk/2, csb_clk/3
Off, csb_clk
Off, csb_clk, csb_clk/2, csb_clk/3
Options
Eqn. 20
Eqn. 21
Eqn. 22
Clocking
107