Z8F16800144ZCOG Zilog, Z8F16800144ZCOG Datasheet - Page 321
Z8F16800144ZCOG
Manufacturer Part Number
Z8F16800144ZCOG
Description
KIT DEV FOR Z8F642 MCU 44 PIN
Manufacturer
Zilog
Series
Z8 Encore!®r
Type
MCUr
Specifications of Z8F16800144ZCOG
Contents
Hardware, Software and Documentation
For Use With/related Products
Z8F642
For Use With
269-4661 - KIT ACC ETHERNET SMART CABLE
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
Other names
269-4678
- Current page: 321 of 399
- Download datasheet (19Mb)
®
Z8 Encore! XP
F1680 Series
Product Specification
307
When selecting a new clock source, the primary oscillator failure detection circuitry and
the Watchdog Timer oscillator failure circuitry must be disabled. If POFEN and WOFEN
are not disabled prior to a clock switch-over, it is possible to generate an interrupt for a
failure of either oscillator. The Failure detection circuitry can be enabled anytime after a
successful write of SCKSEL in the oscillator control register.
The internal precision oscillator is enabled by default. If the user code changes to a
different oscillator, it may be appropriate to disable the IPO for power savings. Disabling
the IPO does not occur automatically.
Clock Failure Detection and Recovery
Primary Oscillator Failure
The Z8 Encore! XP F1680 Series devices can generate non-maskable interrupt-like events
when the primary oscillator fails. To maintain system function in this situation, the clock
failure recovery circuitry automatically forces the Watchdog Timer oscillator to drive the
system clock. The Watchdog Timer oscillator must be enabled to allow the recovery.
Although this oscillator runs at a much slower speed than the original system clock, the
CPU continues to operate allowing execution of a clock failure vector and software
routines that either remedy the oscillator failure or issue a failure alert. This automatic
switch-over is not available, if the Watchdog Timer is the primary oscillator. It is also
unavailable if the Watchdog Timer oscillator is disabled, though it is not necessary to
enable the Watchdog Timer reset function outlined in
Watchdog Timer
chapter of this
document on page 137.
The primary oscillator failure detection circuitry asserts if the system clock frequency
drops below 1 kHz ±50%. If an external signal is selected as the system oscillator, it is
possible that a very slow but non-failing clock can generate a failure condition. Under
these conditions, do not enable the clock failure circuitry (POFEN must be removed from
the OSCCTL0 register).
Watchdog Timer Failure
In the event of a Watchdog Timer oscillator failure, a similar non-maskable interrupt-like
event is issued. This event does not trigger an attendant clock switch-over, but alerts the
CPU of the failure. After a Watchdog Timer failure, it is no longer possible to detect a pri-
mary oscillator failure. The failure detection circuitry does not function if the Watchdog
Timer is used as the primary oscillator or if the Watchdog Timer oscillator has been dis-
abled. For either of these cases, it is necessary to disable the detection circuitry by remov-
ing the WDFEN bit of the OSCCTL0 register.
The Watchdog Timer oscillator failure-detection circuit counts system clocks while
looking for a Watchdog Timer clock. The logic counts 8004 system clock cycles before
determining that a failure has occurred. The system clock rate determines the speed at
which the Watchdog Timer failure can be detected. A very slow system clock results in
very slow detection times.
PS025011-1010
P R E L I M I N A R Y
Oscillator Control
Related parts for Z8F16800144ZCOG
Image
Part Number
Description
Manufacturer
Datasheet
Request
R
Part Number:
Description:
Communication Controllers, ZILOG INTELLIGENT PERIPHERAL CONTROLLER (ZIP)
Manufacturer:
Zilog, Inc.
Datasheet:
Part Number:
Description:
KIT DEV FOR Z8 ENCORE 16K TO 64K
Manufacturer:
Zilog
Datasheet:
Part Number:
Description:
KIT DEV Z8 ENCORE XP 28-PIN
Manufacturer:
Zilog
Datasheet:
Part Number:
Description:
DEV KIT FOR Z8 ENCORE 8K/4K
Manufacturer:
Zilog
Datasheet:
Part Number:
Description:
KIT DEV Z8 ENCORE XP 28-PIN
Manufacturer:
Zilog
Datasheet:
Part Number:
Description:
DEV KIT FOR Z8 ENCORE 4K TO 8K
Manufacturer:
Zilog
Datasheet:
Part Number:
Description:
CMOS Z8 microcontroller. ROM 16 Kbytes, RAM 256 bytes, speed 16 MHz, 32 lines I/O, 3.0V to 5.5V
Manufacturer:
Zilog, Inc.
Datasheet:
Part Number:
Description:
Low-cost microcontroller. 512 bytes ROM, 61 bytes RAM, 8 MHz
Manufacturer:
Zilog, Inc.
Datasheet:
Part Number:
Description:
Z8 4K OTP Microcontroller
Manufacturer:
Zilog, Inc.
Datasheet:
Part Number:
Description:
CMOS SUPER8 ROMLESS MCU
Manufacturer:
Zilog, Inc.
Datasheet:
Part Number:
Description:
SL1866 CMOSZ8 OTP Microcontroller
Manufacturer:
Zilog, Inc.
Datasheet:
Part Number:
Description:
SL1866 CMOSZ8 OTP Microcontroller
Manufacturer:
Zilog, Inc.
Datasheet:
Part Number:
Description:
OTP (KB) = 1, RAM = 125, Speed = 12, I/O = 14, 8-bit Timers = 2, Comm Interfaces Other Features = Por, LV Protect, Voltage = 4.5-5.5V
Manufacturer:
Zilog, Inc.
Datasheet:
Part Number:
Description:
Manufacturer:
Zilog, Inc.
Datasheet: