AT91CAP7E-NA-ZJ Atmel, AT91CAP7E-NA-ZJ Datasheet - Page 270

• Manufacturer Part Number: AT91CAP7E-NA-ZJ
• Description: MCU CAP7 FPGA 225LFBGA
• Manufacturer: Atmel
• Series: CAP™r

Specifications of AT91CAP7E-NA-ZJ

• Core Processor: ARM7
• Core Size: 16/32-Bit
• Speed: 80MHz
• Connectivity: EBI/EMI, FPGA, IrDA, SPI, UART/USART, USB
• Peripherals: DMA, POR, PWM, WDT
• Number Of I /o: 32
• Program Memory Size: 256KB (256K x 8)
• Program Memory Type: ROM
• Ram Size: 160K x 8
• Voltage - Supply (vcc/vdd): 1.08 V ~ 1.32 V
• Data Converters: A/D 8x10b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 225-LFBGA
• Processor Series: AT91Mx
• Core: ARM7TDMI
• Data Bus Width: 32 bit
• 3rd Party Development Tools: JTRACE-ARM-2M, MDK-ARM, RL-ARM, ULINK2
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Eeprom Size: -
• Lead Free Status / Rohs Status: Details

Figure 26-8. Parity Error
26.4.3.4
Figure 26-9. Receiver Framing Error
26.4.4
26.4.4.1
26.4.4.2
270
AT91CAP7E
Transmitter
Receiver Framing Error
Transmitter Reset, Enable and Disable
Transmit Format
RXRDY
FRAME
DRXD
PARE
RXRDY
DRXD
bit. If different, the parity error bit PARE in DBGU_SR is set at the same time the RXRDY is set.
The parity bit is cleared when the control register DBGU_CR is written with the bit RSTSTA
(Reset Status) at 1. If a new character is received before the reset status command is written,
the PARE bit remains at 1.
When a start bit is detected, it generates a character reception when all the data bits have been
sampled. The stop bit is also sampled and when it is detected at 0, the FRAME (Framing Error)
bit in DBGU_SR is set at the same time the RXRDY bit is set. The bit FRAME remains high until
the control register DBGU_CR is written with the bit RSTSTA at 1.
After device reset, the Debug Unit transmitter is disabled and it must be enabled before being
used. The transmitter is enabled by writing the control register DBGU_CR with the bit TXEN at 1.
From this command, the transmitter waits for a character to be written in the Transmit Holding
Register DBGU_THR before actually starting the transmission.
The programmer can disable the transmitter by writing DBGU_CR with the bit TXDIS at 1. If the
transmitter is not operating, it is immediately stopped. However, if a character is being pro-
cessed into the Shift Register and/or a character has been written in the Transmit Holding
Register, the characters are completed before the transmitter is actually stopped.
The programmer can also put the transmitter in its reset state by writing the DBGU_CR with the
bit RSTTX at 1. This immediately stops the transmitter, whether or not it is processing
characters.
The Debug Unit transmitter drives the pin DTXD at the baud rate clock speed. The line is driven
depending on the format defined in the Mode Register and the data stored in the Shift Register.
One start bit at level 0, then the 8 data bits, from the lowest to the highest bit, one optional parity
bit and one stop bit at 1 are consecutively shifted out as shown on the following figure. The field
S
S
D0
D0
D1
D1
D2
D2
D3
D3
D4
D4
D5
D5
D6
D6
Wrong Parity Bit
D7
D7
P
P
Detected at 0
Stop Bit
stop
stop
RSTSTA
RSTSTA
8549A–CAP–10/08