C8051F930-GQ Silicon Laboratories Inc, C8051F930-GQ Datasheet - Page 22

• Manufacturer Part Number: C8051F930-GQ
• Description: IC 8051 MCU 64K FLASH 32-LQFP
• Manufacturer: Silicon Laboratories Inc
• Series: C8051F9xxr

Specifications of C8051F930-GQ

• Program Memory Type: FLASH
• Program Memory Size: 64KB (64K x 8)
• Package / Case: 32-LQFP
• Core Processor: 8051
• Core Size: 8-Bit
• Speed: 25MHz
• Connectivity: SMBus (2-Wire/I²C), SPI, UART/USART
• Peripherals: Brown-out Detect/Reset, POR, PWM, Temp Sensor, WDT
• Number Of I /o: 24
• Ram Size: 4.25K x 8
• Voltage - Supply (vcc/vdd): 0.9 V ~ 3.6 V
• Data Converters: A/D 23x10b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Processor Series: C8051F9x
• Core: 8051
• Data Bus Width: 8 bit
• Data Ram Size: 4.25 KB
• Interface Type: I2C/SMBus/SPI/UART
• Maximum Clock Frequency: 25 MHz
• Number Of Programmable I/os: 24
• Number Of Timers: 4
• Operating Supply Voltage: 0.9 V to 3.6 V
• Maximum Operating Temperature: + 85 C
• Mounting Style: SMD/SMT
• 3rd Party Development Tools: PK51, CA51, A51, ULINK2
• Development Tools By Supplier: C8051F930DK
• Minimum Operating Temperature: - 40 C
• On-chip Adc: 23-ch x 10-bit
• No. Of I/o's: 24
• Ram Memory Size: 4KB
• Cpu Speed: 25MHz
• No. Of Timers: 4
• Rohs Compliant: Yes
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• For Use With: 336-1478 - PLATFORM PROG TOOLSTCK F920,F930336-1477 - PLATFORM PROG TOOLSTCK F920,F930336-1473 - KIT DEV C8051F920,F921,F930,F931336-1472 - BOARD TARGET/PROTO W/C8051F930
• Eeprom Size: -
• Lead Free Status / Rohs Status: Lead free / RoHS Compliant
• Other names: 336-1466

C8051F93x-C8051F92x
as GPIO and is shared with the C2 Interface Data signal (C2D). See Section “27. C2 Interface” on
page 319 for more details.
The designer has complete control over which digital and analog functions are assigned to individual Port
pins, limited only by the number of physical I/O pins. This resource assignment flexibility is achieved
through the use of a Priority Crossbar Decoder. See Section “21.3. Priority Crossbar Decoder” on
page 216 for more information on the Crossbar.
All Port I/Os are 5 V tolerant when used as digital inputs or open-drain outputs. For Port I/Os configured as
push-pull outputs, current is sourced from the VDD/DC+ supply. Port I/Os used for analog functions can
operate up to the VDD/DC+ supply voltage. See Section “21.1. Port I/O Modes of Operation” on page 213
for more information on Port I/O operating modes and the electrical specifications chapter for detailed elec-
trical specifications.
1.3.
The C8051F93x-C8051F92x Family includes an SMBus/I
baud rate configuration, and two Enhanced SPI interfaces. Each of the serial buses is fully implemented in
hardware and makes extensive use of the CIP-51's interrupts, thus requiring very little CPU intervention.
22
Highest
Priority
Lowest
Priority
Serial Ports
SYSCLK
Outputs
SMBus
T0, T1
UART
P0
P1
P2
SPI0
SPI1
CP0
CP1
PCA
(P0.0-P0.7)
(P1.0-P1.7)
(P2.0-P2.7)
Figure 1.5. Port I/O Functional Block Diagram
2
4
2
4
7
2
8
8
8
Rev. 1.1
XBR2, PnSKIP
XBR0, XBR1,
Crossbar
Decoder
Registers
Priority
Digital
(ADC0, CP0, and CP1 inputs,
2
C interface, a full-duplex UART with enhanced
To EMIF
To Analog Peripherals
VREF, IREF0, AGND)
8
8
8
P0MASK, P0MAT
P1MASK, P1MAT
Port Match
Cells
Cells
Cell
I/O
I/O
I/O
P0
P1
P2
PnMDIN Registers
External Interrupts
EX0 and EX1
PnMDOUT,
P1.7–2.6 only available
P2.7 is available on all
on 32-pin devices
devices
P0.0
P0.7
P1.0
P1.6
P1.7
P2.0
P2.6
P2.7