C8051F930-GQ Silicon Laboratories Inc, C8051F930-GQ Datasheet - Page 263

• Manufacturer Part Number: C8051F930-GQ
• Description: IC 8051 MCU 64K FLASH 32-LQFP
• Manufacturer: Silicon Laboratories Inc
• Series: C8051F9xxr

Specifications of C8051F930-GQ

• Program Memory Type: FLASH
• Program Memory Size: 64KB (64K x 8)
• Package / Case: 32-LQFP
• Core Processor: 8051
• Core Size: 8-Bit
• Speed: 25MHz
• Connectivity: SMBus (2-Wire/I²C), SPI, UART/USART
• Peripherals: Brown-out Detect/Reset, POR, PWM, Temp Sensor, WDT
• Number Of I /o: 24
• Ram Size: 4.25K x 8
• Voltage - Supply (vcc/vdd): 0.9 V ~ 3.6 V
• Data Converters: A/D 23x10b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Processor Series: C8051F9x
• Core: 8051
• Data Bus Width: 8 bit
• Data Ram Size: 4.25 KB
• Interface Type: I2C/SMBus/SPI/UART
• Maximum Clock Frequency: 25 MHz
• Number Of Programmable I/os: 24
• Number Of Timers: 4
• Operating Supply Voltage: 0.9 V to 3.6 V
• Maximum Operating Temperature: + 85 C
• Mounting Style: SMD/SMT
• 3rd Party Development Tools: PK51, CA51, A51, ULINK2
• Development Tools By Supplier: C8051F930DK
• Minimum Operating Temperature: - 40 C
• On-chip Adc: 23-ch x 10-bit
• No. Of I/o's: 24
• Ram Memory Size: 4KB
• Cpu Speed: 25MHz
• No. Of Timers: 4
• Rohs Compliant: Yes
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• For Use With: 336-1478 - PLATFORM PROG TOOLSTCK F920,F930336-1477 - PLATFORM PROG TOOLSTCK F920,F930336-1473 - KIT DEV C8051F920,F921,F930,F931336-1472 - BOARD TARGET/PROTO W/C8051F930
• Eeprom Size: -
• Lead Free Status / Rohs Status: Lead free / RoHS Compliant
• Other names: 336-1466

24. Enhanced Serial Peripheral Interface (SPI0 and SPI1)
The Enhanced Serial Peripheral Interfaces (SPI0 and SPI1) provide access to two identical, flexible, full-
duplex synchronous serial busses. Both SPI0 and SPI1 will be referred to collectively as SPIn. SPIn can
operate as a master or slave device in both 3-wire or 4-wire modes, and supports multiple masters and
slaves on a single SPI bus. The slave-select (NSS) signal can be configured as an input to select SPIn in
slave mode, or to disable Master Mode operation in a multi-master environment, avoiding contention on
the SPI bus when more than one master attempts simultaneous data transfers. NSS can also be
configured as a chip-select output in master mode, or disabled for 3-wire operation. Additional general
purpose port I/O pins can be used to select multiple slave devices in master mode.
SYSCLK
Clock Divide
SPInCKR
SFR Bus
SPI0DAT
Logic
Write
Transmit Data Buffer
Receive Data Buffer
7
Figure 24.1. SPI Block Diagram
6
Shift Register
5
SPI CONTROL LOGIC
4
3
Data Path
2
SFR Bus
Control
SPInCFG
SPInDAT
1
SPI0DAT
Read
0
Rev. 1.1
Tx Data
Rx Data
Pin Interface
C8051F93x-C8051F92x
Control
Control
Logic
Pin
SPInCN
MOSI
MISO
SCK
NSS
C
R
O
S
S
B
A
R
SPIn IRQ
Port I/O
263