DF38602RFT10 Renesas Electronics America, DF38602RFT10 Datasheet - Page 258

• Manufacturer Part Number: DF38602RFT10
• Description: MCU 3V 16K 32-QFN
• Manufacturer: Renesas Electronics America
• Series: H8® H8/300H SLPr

Specifications of DF38602RFT10

• Core Processor: H8/300H
• Core Size: 16-Bit
• Speed: 10MHz
• Connectivity: I²C, IrDA, SCI, SSU
• Peripherals: POR, PWM, WDT
• Number Of I /o: 13
• Program Memory Size: 16KB (16K x 8)
• Program Memory Type: FLASH
• Ram Size: 1K x 8
• Voltage - Supply (vcc/vdd): 2.7 V ~ 3.6 V
• Data Converters: A/D 6x10b
• Oscillator Type: Internal
• Operating Temperature: -20°C ~ 75°C
• Package / Case: 32-QFN
• Lead Free Status / RoHS Status: Contains lead / RoHS non-compliant
• Eeprom Size: -
• Other names: HD64F38602RFT10; HD64F38602RFT10

Section 13 Asynchronous Event Counter (AEC)
13.4.2
When bit CH2 is set to 1 in ECCSR, ECH and ECL operate as independent 8-bit event counters.
φ/2, φ/4, φ/8, or AEVH pin input can be selected as the input clock source for ECH by means of
bits ACKH1 and ACKH0 in ECCR, and φ/2, φ/4, φ/8, or AEVL pin input can be selected as the
input clock source for ECL by means of bits ACKL1 and ACKL0 in ECCR. Input sensing is
selected with bits AHEGS1 and AHEGS0 when AEVH pin input is selected, and with bits
ALEGS1 and ALEGS0 when AEVL pin input is selected.
Note that the input clock is enabled when IRQAEC is high or IECPWM is high. When IRQAEC is
low or IECPWM is low, the input clock is not input to the counter, which therefore does not
operate. Figure 13.3 shows the software procedure when ECH and ECL are used as 8-bit event
counters.
When the next clock is input after the ECH count value reaches H'FF, ECH overflows, the OVH
flag is set to 1 in ECCSR, the ECH count value returns to H'00, and counting up is restarted.
Similarly, when the next clock is input after the ECL count value reaches H'FF, ECL overflows,
the OVL flag is set to 1 in ECCSR, the ECL count value returns to H'00, and counting up is
restarted. When an overflow occurs, the IRREC bit is set to 1 in IRR2. If the IENEC bit in IENR2
is 1 at this time, an interrupt request is sent to the CPU.
Rev. 3.00 May 15, 2007 Page 224 of 516
REJ09B0152-0300
Figure 13.3 Software Procedure when Using ECH and ECL as 8-Bit Event Counters
8-Bit Counter Operation
Set CH2 to 1
Set ACKH1, ACKH0, ACKL1, ACKL0,
AHEGS1, AHEGS0, ALEGS1, and ALEGS0
Clear CUEH, CUEL, CRCH, and CRCL to 0
Clear OVH and OVL to 0
Set CUEH, CUEL, CRCH, and CRCL to 1
Start
End