M30624FGNGP#D5 Renesas Electronics America, M30624FGNGP#D5 Datasheet - Page 12

• Manufacturer Part Number: M30624FGNGP#D5
• Description: IC M16C MCU FLASH 256K 100LQFP
• Manufacturer: Renesas Electronics America
• Series: M16C™ M16C/60r

Specifications of M30624FGNGP#D5

• Core Processor: M16C/60
• Core Size: 16-Bit
• Speed: 16MHz
• Connectivity: SIO, UART/USART
• Peripherals: DMA, PWM, WDT
• Number Of I /o: 85
• Program Memory Size: 256KB (256K x 8)
• Program Memory Type: FLASH
• Ram Size: 20K x 8
• Voltage - Supply (vcc/vdd): 3 V ~ 3.6 V
• Data Converters: A/D 18x10b, D/A 2x8b
• Oscillator Type: Internal
• Operating Temperature: -20°C ~ 85°C
• Package / Case: 100-LQFP
• Lead Free Status / RoHS Status: Contains lead / RoHS non-compliant
• Eeprom Size: -

Pin Description
Pin Description
P8
P8
P10
ALE,
RDY
P6
P7
P8
P8
P9
WRL / WR,
WRH / BHE,
RD,
BCLK,
HLDA,
HOLD,
P5
Pin name
0
6
7
0
0
5
0
0
,
,
0
to P6
to P7
to P8
to P9
to P5
to P10
4
7
7
7
7
,
7
I/O port P8
I/O port P10
I/O port P5
I/O port P6
I/O port P7
I/O port P8
I/O port P9
Signal name
5
Output
Input
Input/output
Input/output
Input/output
Input/output
Input/output
Input/output
Input
Input/output
Input/output
Output
Output
Output
Output
Output
Input
I/O type
This is an 8-bit I/O port equivalent to P0. In single-chip mode, P5
this port outputs a divide-by-8 or divide-by-32 clock of X
the same frequency as X
Output WRL, WRH (WR and BHE), RD, BCLK, HLDA, and ALE
signals. WRL and WRH, and BHE and WR can be switched using
software control.
With a 16-bit external data bus, data is written to even addresses
when the WRL signal is “L” and to the odd addresses when the WRH
signal is “L”. Data is read when RD is “L”.
Data is written when WR is “L”. Data is read when RD is “L”. Odd
addresses are accessed when BHE is “L”. Use this mode when using
an 8-bit external data bus.
While the input level at the HOLD pin is “L”, the microcomputer is
placed in the hold state. While in the hold state, HLDA outputs a “L”
level. ALE is used to latch the address. While the input level of the
RDY pin is “L”, the microcomputer is in the ready state.
This is an 8-bit I/O port equivalent to P0. When used for input in single-
chip, memory expansion, and microprocessor modes, the port can be
set to have or not have a pull-up resistor in units of four bits by
software. Pins in this port also function as UART0 and UART1 I/O pins
as selected by software.
This is an 8-bit I/O port equivalent to P6 (P7
open-drain output). Pins in this port also function as timer A
timer B5 or UART2 I/O pins as selected by software.
This is an 8-bit I/O port equivalent to P6. Pins in this port also function
as SI/O3, 4 I/O pins, Timer B0–B4 input pins, D-A converter output pins,
A-D converter extended input pins, or A-D trigger input pins as selected
by software.
P8
Using software, they can be made to function as the I/O pins for timer
A4 and the input pins for external interrupts. P8
using software to function as the I/O pins for a sub clock generation
circuit. In this case, connect a quartz oscillator between P8
pin) and P8
for NMI. The NMI interrupt is generated when the input at this pin
changes from “H” to “L”. The NMI function cannot be cancelled using
software. The pull-up cannot be set for this pin.
This is an 8-bit I/O port equivalent to P6. Pins in this port also function
as A-D converter input pins as selected by software. Furthermore, P10
–P10
0
WRL, WRH, and RD selected
WR, BHE, and RD selected
to P8
7
also function as input pins for the key input interrupt function.
4
, P8
7
(X
6
CIN
, and P8
pin). P8
7
CIN
are I/O ports with the same functions as P6.
5
as selected by software.
is an input-only port that also functions
SINGLE-CHIP 16-BIT CMOS MICROCOMPUTER
Function
0
and P7
6
and P8
M16C / 62N Group
Mitsubishi microcomputers
1
are N channel
IN
7
can be set
or a clock of
6
0
(X
–A
COUT
3
,
7
in
4
9