M30624FGNGP#D5 Renesas Electronics America, M30624FGNGP#D5 Datasheet - Page 160

• Manufacturer Part Number: M30624FGNGP#D5
• Description: IC M16C MCU FLASH 256K 100LQFP
• Manufacturer: Renesas Electronics America
• Series: M16C™ M16C/60r

Specifications of M30624FGNGP#D5

• Core Processor: M16C/60
• Core Size: 16-Bit
• Speed: 16MHz
• Connectivity: SIO, UART/USART
• Peripherals: DMA, PWM, WDT
• Number Of I /o: 85
• Program Memory Size: 256KB (256K x 8)
• Program Memory Type: FLASH
• Ram Size: 20K x 8
• Voltage - Supply (vcc/vdd): 3 V ~ 3.6 V
• Data Converters: A/D 18x10b, D/A 2x8b
• Oscillator Type: Internal
• Operating Temperature: -20°C ~ 85°C
• Package / Case: 100-LQFP
• Lead Free Status / RoHS Status: Contains lead / RoHS non-compliant
• Eeprom Size: -

A-D Converter
Table 1.18.3. Repeat mode specifications
Note : AN
Figure 1.18.5. A-D conversion register in repeat mode
(2) Repeat mode
Function
Star condition
Stop condition
Interrupt request generation timing
Input pin
Reading of result of A-D converter
In repeat mode, the pin selected using the analog input pin select bit is used for repeated A-D conversion.
Table 1.18.3 shows the specifications of repeat mode. Figure 1.18.5 shows the A-D control register in
repeat mode.
00
Item
A-D control register 0 (Note 1)
b7
A-D control register 1 (Note)
b7
to AN
b6
b6
b5
b5
1
07
b4
0 1
b4
can be used the same as AN
b3
b3
b2
b2
0
b1
b1
b0
b0
The pin selected by the analog input pin select bit is used for repeated A-D conversion
Writing “1” to A-D conversion start flag
Writing “0” to A-D conversion start flag
None generated
One of AN
Read A-D register corresponding to selected pin (at any time)
Note 1: If the A-D control register is rewritten during A-D conversion, the conversion
Note 2: AN
Note 3: When changing A-D operation mode, set analog input pin again.
Note: If the A-D control register is rewritten during A-D conversion, the conversion
Bit symbol
Bit symbol
SCAN0
SCAN1
VCUT
OPA0
OPA1
ADST
CKS0
CKS1
MD0
MD1
TRG
MD2
BITS
CH0
CH1
CH2
Symbol
ADCON0
Symbol
ADCON1
result is indeterminate.
result is indeterminate.
00
0
to AN
Analog input pin
select bit
A-D sweep pin
select bit
A-D operation mode
select bit 1
8/10-bit mode select bit
Frequency select bit 1
Vref connect bit
A-D operation mode
select bit 0
Trigger select bit
A-D conversion start flag
Frequency select bit 0
External op-amp
connection mode bit
to AN
07
Bit name
Bit name
can be used the same as AN
7
, as selected (Note)
Address
Address
03D6
03D7
0
to AN
16
16
0 0 : ANEX0 and ANEX1 are not used
0 1 : ANEX0 input is A-D converted
1 0 : ANEX1 input is A-D converted
1 1 : External op-amp connection mode
Invalid in repeat mode
0 : 8-bit mode
1 : 10-bit mode
0 : f
1 : f
1 : Vref connected
Set to “0” when this mode is selected
b7 b6
00000XXX
When reset
When reset
7
0 0 0 : AN
0 0 1 : AN
0 1 0 : AN
0 1 1 : AN
1 0 0 : AN
1 0 1 : AN
1 1 0 : AN
1 1 1 : AN
b4 b3
0 1 : Repeat mode
0 : Software trigger
1 : AD
0 : A-D conversion disabled
1 : A-D conversion started
0 : f
1 : f
b2 b1 b0
Specification
.
AD
AD
00
AD
AD
/2 or f
is selected
16
/4 is selected
/2 is selected
TRG
0
1
2
3
4
5
6
7
trigger
AD
2
is selected
is selected
is selected
is selected
is selected
is selected
is selected
is selected
SINGLE-CHIP 16-BIT CMOS MICROCOMPUTER
/4 is selected
0
to AN
Function
Function
7
.
(Note 2)
(Note 3)
(Note 3)
M16C / 62N Group
Mitsubishi microcomputers
R
R
W
W
157