EP2AGX45DF29I5 Altera, EP2AGX45DF29I5 Datasheet - Page 361

• Manufacturer Part Number: EP2AGX45DF29I5
• Description: IC ARRIA II GX FPGA 45K 780FBGA
• Manufacturer: Altera
• Series: Arria II GXr

Specifications of EP2AGX45DF29I5

• Number Of Logic Elements/cells: 42959
• Number Of Labs/clbs: 1805
• Total Ram Bits: 3435
• Number Of I /o: 364
• Voltage - Supply: 0.87 V ~ 0.93 V
• Mounting Type: Surface Mount
• Operating Temperature: -40°C ~ 100°C
• Package / Case: 780-FBGA
• Lead Free Status / RoHS Status: Contains lead / RoHS non-compliant
• Number Of Gates: -

© 2010 Altera Corporation. All rights reserved. ALTERA, ARRIA, CYCLONE, HARDCOPY, MAX, MEGACORE, NIOS, QUARTUS and STRATIX are Reg. U.S. Pat. & Tm. Off.
and/or trademarks of Altera Corporation in the U.S. and other countries. All other trademarks and service marks are the property of their respective holders as described at
www.altera.com/common/legal.html. Altera warrants performance of its semiconductor products to current specifications in accordance with Altera’s standard warranty, but
reserves the right to make changes to any products and services at any time without notice. Altera assumes no responsibility or liability arising out of the application or use of any
information, product, or service described herein except as expressly agreed to in writing by Altera. Altera customers are advised to obtain the latest version of device
specifications before relying on any published information and before placing orders for products or services.
AIIGX51011-4.0
BST Architecture for Arria II Devices
Arria II Device Handbook Volume 1: Device Interfaces and Integration
December 2010
December 2010
AIIGX51011-4.0
IEEE Std. 1149.6 Boundary-Scan Register for Arria II GX Devices
f
This chapter describes the boundary-scan test (BST) features that are supported in
Arria
Arria II devices. The features are similar to Arria GX devices, unless stated in this
chapter.
This chapter includes the following sections:
■
■
■
■
■
Arria II GX devices support IEEE Std. 1149.1 and IEEE Std. 1149.6, while Arria II GZ
devices support IEEE Std. 1149.1 only. The IEEE Std. 1149.6 is only supported on the
high-speed serial interface (HSSI) transceivers in Arria II GX devices. The IEEE Std.
1149.6 enables board-level connectivity checking between transmitters and receivers
that are AC coupled (connected with a capacitor in series between the source and
destination).
For Arria II GX devices, the TDO output pin and all JTAG input pins are powered by
the V
pin and all the JTAG input pins are powered by 2.5-V/3.0-V V
Bank 1A. All user I/O pins are tri-stated during JTAG configuration.
For more information about the IEEE Std. 1149.1 BST architecture, BST circuitry, and
boundary-scan register for Arria II devices, refer to the
Boundary-Scan Testing for Arria GX Devices
Handbook.
The boundary-scan cell (BSC) for HSSI transmitters (GXB_TX[p,n]) and
receivers/input clock buffer (GXB_RX[p,n])/(REFCLK[0..7]) in Arria II GX devices are
different from the BSCs for I/O pins.
“BST Architecture for Arria II Devices” on page 11–1
“BST Operation Control” on page 11–3
“I/O Voltage Support in a JTAG Chain” on page 11–5
“Disabling IEEE Std. 1149.1 BST Circuitry” on page 11–6
“Boundary-Scan Description Language Support” on page 11–7
®
CCIO
II devices and how to use the IEEE Std. 1149.1 and Std. 1149.6 BST circuitries in
power supply of I/O Bank 8C, while for Arria II GZ devices, the TDO output
11. JTAG Boundary-Scan Testing in
chapter in volume 2 of the Arria GX Device
IEEE 1149.1 (JTAG)
Arria II Devices
CCPD
supply of I/O
Subscribe