TMPM333FDFG Toshiba, TMPM333FDFG Datasheet - Page 353

• Manufacturer Part Number: TMPM333FDFG
• Description: Microcontrollers (MCU) MCU w/ ARM Cortex-M3 512K FLASH, 32K SRAM
• Manufacturer: Toshiba

Specifications of TMPM333FDFG

• Processor Series: TX03
• Core: ARM Cortex M3
• 3rd Party Development Tools: MDK-ARM, RL-ARM, ULINK2
• Product Summaries: Summary
• Lead Free: Yes
• Rohs Compatible Product(s): Available
• Rom (kbytes): 512K
• Rom Type: Flash
• Ram (kbytes): 32K
• Number Of Pins: 100
• Package: LQFP(14×14)
• Vcc: 3V
• Cpu Mhz: 40
• Ssp (ch) Spi: -
• I2c/sio (ch): 3
• Uart/sio (ch): 3
• Usb: -
• Can: -
• Ethernet: -
• External Bus Interface: -
• Cs/wait Controller (ch): -
• Dma Controller: -
• 10-bit Da Converter: -
• 10-bit Ad Converter: 12
• 12-bit Ad Converter: -
• 16-bit Timer / Counter: 10
• Motor / Igbt Control: -
• Real Time Clock: 1
• Watchdog Timer: Y
• Osc Freq Detect: -
• Clock Gear: Y
• Low-power Hold Function: -
• Remote Control Interface: -
• Hardware Cec Controller: -
• Comparators: -
• Low-voltage Detector: -
• Etm Hardware Trace: 4-bit
• Lead Free Status / Rohs Status: Details

12.4.3
12.4.2.2
If the value of the conversion result register specified by ADMOD3<ADREGS0> and ADMOD5<ADREGS1>
becomes larger or smaller ("Larger" or "Smaller" to be designated by ADMOD3<ADOBIC0> and AD-
MOD5<ADBIC1>) than the value of a comparison register, the AD monitor function interrupt (INTADM0,IN-
TADM1) is generated. This comparison operation is performed each time a result is stored in a corresponding
conversion result register.
reading the conversion result, the conversion result is overwritten. The conversion result storage flag <ADRxRF>
and the overrun flag <OVRx> remain being set.
There are two channels of AD monitor function.
If ADMOD3<ADOBSV0> and ADMOD5<ADOBSV1> are set to "1", the AD monitor function is enabled.
If the conversion result register assigned to perform the AD monitor function is continuously used without
SCAN> setting. When conditions to start operation are met, a conversion is performed just once for a channel
designated by ADMOD2<HPADCH>. When conversion is completed, the top-priority AD conversion com-
pletion interrupt (INTADHP) is generated, and ADMOD2<EOCFHP> showing the completion of AD
conversion is set to "1". <ADBFHP> returns to "0". EOCFHP flag is cleared to "0" upon read.
AD Monitor Function
(3)
(4)
By interrupting ongoing normal AD conversion, top-priority AD conversion can be performed.
The fixed-channel single conversion is automatically selected, irrespective of the ADMOD0<REPEAT,
Top-priority AD conversion activated while top-priority AD conversion is under way is ignored.
Top-priority AD conversion
conversation mode.
is completed, ADMOD0<EOCFN> is set to "1". ADMOD0<ADBFN> is not cleared to "0". It remains
at "1". The timing with which the conversion completion interrupt request (INTAD) is generated can
be selected by setting ADMOD0<ITM> to an appropriate setting. <EOCFN> is set with the same timing
as this interrupt INTAD is generated.
conversion mode.
scan conversion is completed, ADMOD0<EOCFN> is set to "1", and the conversion completion inter-
rupt request (INTAD) is generated. ADMOD0<ADBFN> is not cleared to "0". It remains at "1".
<EOCFN> is cleared to "0" upon read.
If ADMOD0<REPEAT, SCAN> is set to "10", AD conversion is performed in fixed channel repeat
In this mode, AD conversion is performed repeatedly for one channel selected. After AD conversion
By reading <EOCFN>, it is cleared to "0".
If ADMOD0<REPEAT, SCAN> is set to "11", AD conversion is performed in the channel scan repeat
In this mode, AD conversion is performed repeatedly for a scan channel selected. Each time one AD
Fixed channel repeat conversion mode
Channel scan repeat conversion mode
Page 333
TMPM333FDFG/FYFG/FWFG