TMPM363F10FG Toshiba, TMPM363F10FG Datasheet - Page 610

• Manufacturer Part Number: TMPM363F10FG
• Manufacturer: Toshiba

Specifications of TMPM363F10FG

• Product Summaries: Summary
• Lead Free: Yes
• Rohs Compatible Product(s): Available
• Rom (kbytes): 1024K
• Rom Type: Flash
• Ram (kbytes): 64K
• Number Of Pins: 100
• Package: LQFP(14x14)
• Vcc: 3V
• Cpu Mhz: 64
• Ssp (ch) Spi: 1
• I2c/sio (ch): 4
• Uart/sio (ch): 5
• Usb: Host
• Can: 1
• Ethernet: -
• External Bus Interface: Y
• Cs/wait Controller (ch): 4
• Dma Controller: 2
• 10-bit Da Converter: 8
• 10-bit Ad Converter: 8
• 12-bit Ad Converter: -
• 16-bit Timer / Counter: 16
• Motor / Igbt Control: -
• Real Time Clock: Y
• Watchdog Timer: Y
• Osc Freq Detect: -
• Clock Gear: Y
• Low-power Hold Function: Y
• Remote Control Interface: Y
• Hardware Cec Controller: Y
• Comparators: -
• Low-voltage Detector: -
• Etm Hardware Trace: 4-bit

18.6
Register
9
8
7-5
4
3
2
Bit
LSDA
PPS
−
PRS
POCI
PSS
Bit Symbol
R/W
R/W
−
R/W
R/W
R/W
(HCD)
Type
R/W
R/W
−
R/W
R/W
R/W
Type
(HC)
(read)Low Speed Device Attached
This bit indicates the speed of the device attached to this port. When set, a Low Speed device is at-
tached to this port. When clear, a Full Speed device is attached to this port. This field is valid on-
ly when the CurrentConnectStatus is set.
0: Full speed device attached.
1: Low speed device attached.
(write)Clear Port Power
The HCD clears the PortPowerStatus bit by writing a "1" to this bit. Writing a "0" has no effect.
(read)Port Power Status
This bit reflects the port's power status, regardless of the type of power switching implemented.
This bit is cleared if an overcurrent condition is detected. HCD sets this bit by writing SetPortPow-
er or SetGlobalPower. HCD clears this bit by writing ClearPortPower or ClearGlobalPower. Which
power control switches are enabled is determined by PowerSwitchingMode and PortPortControl-
Mask[NDP]. In global switching mode (PowerSwitchingMode="0"), only Set/ClearGlobalPower con-
trols this bit. In per-port power switching (PowerSwitchingMode="1"), if the PortPowerControlMask
[NDP] bit for the port is set, only Set/ClearPortPower commands are enabled. If the mask is not
set, only Set/ClearGlobalPower commands are enabled. When port power is disabled, CurrentCon-
nectStatus, PortEnableStatus, PortSuspendStatus, and PortResetStatus should be reset.
0: Port power off
1: Port power on
(write)Set Port Power
The HCD writes a '1' to set the PortPowerStatus bit. Writing a '0' has no effect.
(Note)
This bit is always reads "1" if power switching is not supported.
Reserved
(read)Port Reset Status
When this bit is set by a write to SetPortReset, port reset signaling is asserted. When reset is com-
pleted, this bit is cleared when PortResetStatusChange is set. This bit cannot be set if CurrentCon-
nectStatus is cleared.
0: Port reset signal is not active
1: Port reset signal is active
(write)Set Port Reset
The HCD sets the port reset signaling by writing a "1" to this bit. Writing a "0" has no effect. If Cur-
rentConnectStatus is cleared, this write does not set PortResetStatus, but instead sets ConnectSta-
tusChange. This informs the driver that it attempted to reset a disconnected port.
(read)Port Over Current Indicator
This bit is only valid when the Root Hub is configured in such a way that overcurrent conditions
are reported on a per-port basis. If per-port overcurrent reporting is not supported, this bit is set
to "0". If cleared, all power operations are normal for this port. If set, an overcurrent condition ex-
ists on this port. This bit always reflects the overcurrent input signal
0: No overcurrent condition
1: Overcurrent condition detected
(write)ClearSuspendStatus
The HCD writes a "1" to initiate a resume. Writing a "0" has no effect. A resume is initiated only if
PortSuspendStatus is set.
(read)Port Suspend Status
This bit indicates the port is suspended or in the resume sequence. It is set by a SetSuspend-
State write and cleared when PortSuspendStatusChange is set at the end of the resume interval.
This bit cannot be set if CurrentConnectStatus is cleared. This bit is also cleared when PortReset-
StatusChange is set at the end of the port reset or when the HC is placed in the USBRESUME
state. If an upstream resume is in progress, it should propagate to the HC.
0: Port is not suspended.
1: Port is suspended.
(write)Set Port Suspend
The HCD sets the PortSuspendStatus bit by writing a "1" to this bit. Writing a "0" has no effect. If Cur-
rentConnectStatus is cleared, this write does not set PortSuspendStatus; instead it sets ConnectSta-
tusChange. This informs the driver that it attempted to suspend a disconnected port.
Page 584
Function
TMPM363F10FG