PNX1502E,557 NXP Semiconductors, PNX1502E,557 Datasheet - Page 468

• Manufacturer Part Number: PNX1502E,557
• Description: IC MEDIA PROC 300MHZ 456-BGA
• Manufacturer: NXP Semiconductors

Specifications of PNX1502E,557

• Applications: Multimedia
• Core Processor: TriMedia
• Controller Series: Nexperia
• Interface: I²C, 2-Wire Serial
• Number Of I /o: 61
• Voltage - Supply: 1.23 V ~ 1.37 V
• Operating Temperature: 0°C ~ 85°C
• Mounting Type: Surface Mount
• Package / Case: 456-BGA
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Program Memory Type: -
• Ram Size: -
• Lead Free Status / Rohs Status: Not Compliant
• Other names: 935274744557; PNX1502E; PNX1502E

Philips Semiconductors
Volume 1 of 1
PNX15XX_SER_3
Product data sheet
2.7.1 BUF1DONE and BUF2DONE Interrupts
2.7.2 THRESH1_REACHED and THRESH2_REACHED Interrupts
2.4 Record or Message Size
2.5 Records or Messages Per Buffer
2.6 Stride
2.7 Interrupt Events
The number of samples per record is set by FGPO_REC_SIZE field. This is amount
of data that will be output after each record or message start event unless the
FGPO_CTL.VAR_LENGTH bit is set. If the FGPO_CTL.VAR_LENGTH bit is set the
length of a record or message is set by the value of the second 32-bit word read from
the header attached to the record or message.
Valid values are in the range of 2 to 2
Remark: The FGPI has a minimum message size of 2 or 3. See FGPI Module
specification for more information.
The number of records or messages per buffer is set by FGPO_SIZE register.
Valid values are in the range of 1 to 2
If the number of records or messages per buffer is greater than one, the address
stride has to be programmed into the FGPO_STRIDE register.
Output starts at a new location in the current buffer on each record or message start
event. After output starts a new address is generated by adding the contents of the
FGPO_STRIDE register to the previous starting address.
Care must be taken that FGPO_STRIDE is greater than or equal to
FGPO_REC_SIZE. Add 8 if either TSTAMP_SELECT or VAR_LENGTH bits are set.
The FGPO_IR_STATUS register contains status and interrupt event status. To
generate an interrupt to the TriMedia processor the corresponding FGPO_IR_ENA bit
must be set. To clear an interrupt event (acknowledge the interrupt) a ‘1’ must be
written to the corresponding FGPO_IR_CLR bit. The FGPO_IR_SET register can be
used to generate software interrupts.
When the number of records or messages output from a main memory buffer equals
the value in the FGPO_SIZE register an associated Buffer Done interrupt will be
generated.
Remark: This interrupt is generated when the FGPO Engine finishes sending the last
sample from the last record/message from the associated main memory buffer.
When FGPO_NRECn (the number of records or messages output from memory
buffer n) equals the contents of the FGPO_THRESHn register then the associated
THRESHn_REACHED bit will be set in the FGPO_IR_STATUS register.
Rev. 3 — 17 March 2006
Chapter 13: FGPO: Fast General Purpose Output
24
24
- 1.
- 1.
© Koninklijke Philips Electronics N.V. 2006. All rights reserved.
PNX15xx Series
13-7