ATA6613-EK Atmel, ATA6613-EK Datasheet - Page 15

• Manufacturer Part Number: ATA6613-EK
• Description: BOARD DEMO LIN-MCM FOR ATA6613
• Manufacturer: Atmel

Specifications of ATA6613-EK

• Main Purpose: Interface, LIN + MCU
• Embedded: Yes, MCU, 8-Bit
• Utilized Ic / Part: ATA6613
• Primary Attributes: LIN-SBC (System-Basis-Chip) Transceiver, LIN 2.0, Voltage Regulator, Window Watchdog
• Secondary Attributes: 16 kB Flash, 4 Power Modes: Pre-Normal, Normal, Sleep, Silent, 48-QFN
• Lead Free Status / RoHS Status: Contains lead / RoHS non-compliant

3.3.21
3.3.21.1
3.3.21.2
3.3.21.3
3.3.21.4
9111H–AUTO–01/11
Wake-up Scenarios from Silent to Sleep Mode
Remote Wake-up via Dominant Bus State
Local Wake-up via Pin Wake
Local Wake-up via Pin KL_15
Wake-up Source Recognition
A voltage less than the LIN Pre_Wake detection V
receiver.
A falling edge at the LIN pin followed by a dominant bus level V
time period (t
switches from Silent or Sleep Mode to Fail-safe Mode. The VCC voltage regulator is/remains
activated, the INH pin is switched to high, and remote wake-up request is indicated by a low
level at the RXD pin to generate an interrupt for the microcontroller. A low level at the LIN pin
in the Normal Mode starts the bus wake-up filtering time, and if the IC is switched to Silent or
Sleep Mode, it will receive a wake-up after a positive edge at the LIN pin.
A falling edge at the WAKE pin followed by a low level maintained for a certain time period
(t
wake-up request is indicated by a low level at the RXD pin to generate an interrupt in the
microcontroller and a strong pull down at TXD. When the Wake pin is low, it is possible to
switch to Silent or Sleep Mode via pin EN. In this case, the wake-up signal has to be switched
to high > 10µs before the negative edge at WAKE starts a new local wake-up request.
A positive edge at pin KL_15 followed by a high voltage level for a certain time period (> t
results in a local wake-up request. The device switches into the Fail-safe Mode. The extra long
wake-up time ensures that no transients at KL_15 create a wake up. The local wake-up
request is indicated by a low level at the RXD pin to generate an interrupt for the microcon-
troller and a strong pull down at TXD. During high-level voltage at pin KL_15, it is possible to
switch to Silent or Sleep Mode via pin EN. In this case, the wake-up signal has to be switched
to low > 250µs before the positive edge at KL_15 starts a new local wake-up request. With
external RC combination, the time is even longer.
The device can distinguish between a local wake-up request (Wake or KL_15 pins) and a
remote wake-up request (via LIN bus). The wake-up source can be read on the TXD pin in
Fail-safe Mode. A high level indicates a remote wake-up request (weak pull up at the TXD
pin); a low level indicates a local wake-up request (strong pull down at the TXD pin). The
wake-up request flag (signalled on the RXD pin), as well as the wake-up source flag (signalled
on the TXD pin), is immediately reset if the microcontroller sets the EN pin to high (see
3-3 on page 11
source flag is stored and signalled in Fail-safe Mode at the TXD pin.
WAKE
) results in a local wake-up request. The device switches to Fail-safe Mode. The local
BUS
and
) and a rising edge at pin LIN result in a remote wake-up request. The device
Figure 3-4 on page
12) and the IC is in Normal Mode. The last wake-up
Atmel ATA6612/ATA6613
LINL
at the LIN pin activates the internal LIN
BUSdom
maintained for a certain
Figure
KL_15
15
)