ATA6613-EK Atmel, ATA6613-EK Datasheet - Page 348

• Manufacturer Part Number: ATA6613-EK
• Description: BOARD DEMO LIN-MCM FOR ATA6613
• Manufacturer: Atmel

Specifications of ATA6613-EK

• Main Purpose: Interface, LIN + MCU
• Embedded: Yes, MCU, 8-Bit
• Utilized Ic / Part: ATA6613
• Primary Attributes: LIN-SBC (System-Basis-Chip) Transceiver, LIN 2.0, Voltage Regulator, Window Watchdog
• Secondary Attributes: 16 kB Flash, 4 Power Modes: Pre-Normal, Normal, Sleep, Silent, 48-QFN
• Lead Free Status / RoHS Status: Contains lead / RoHS non-compliant

7.4
Note:
348
Address
(0x7D)
(0x7C)
(0x7B)
(0x7A)
(0x6E)
(0x6D)
(0x6C)
(0x6B)
(0x6A)
(0x79)
(0x78)
(0x77)
(0x76)
(0x75)
(0x74)
(0x73)
(0x72)
(0x71)
(0x70)
(0x6F)
(0x69)
(0x68)
(0x67)
(0x66)
(0x65)
(0x64)
(0x63)
(0x62)
(0x61)
(0x60)
Register Summary (Continued)
1. For compatibility with future devices, reserved bits should be written to zero if accessed. Reserved I/O memory addresses
2. I/O Registers within the address range 0x00 - 0x1F are directly bit-accessible using the SBI and CBI instructions. In these
3. Some of the Status Flags are cleared by writing a logical one to them. Note that, unlike most other AVRs, the CBI and SBI
4. When using the I/O specific commands IN and OUT, the I/O addresses 0x00 - 0x3F must be used. When addressing I/O
5. Only valid for Atmel ATA6612/ATA6613
Atmel ATA6612/ATA6613
should never be written.
registers, the value of single bits can be checked by using the SBIS and SBIC instructions.
instructions will only operate on the specified bit, and can therefore be used on registers containing such Status Flags. The
CBI and SBI instructions work with registers 0x00 to 0x1F only.
Registers as data space using LD and ST instructions, 0x20 must be added to these addresses. The Atmel
ATA6612/ATA6613 is a complex microcontroller with more peripheral units than can be supported within the 64 location
reserved in Opcode for the IN and OUT instructions. For the Extended I/O space from 0x60 - 0xFF in SRAM, only the
ST/STS/STD and LD/LDS/LDD instructions can be used.
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
WDTCSR
ADCSRB
ADCSRA
PCMSK2
PCMSK1
PCMSK0
OSCCAL
ADMUX
TIMSK2
TIMSK1
TIMSK0
CLKPR
PCICR
EICRA
ADCH
Name
ADCL
PRR
PCINT23
CLKPCE
PCINT7
REFS1
PRTWI
ADEN
WDIF
Bit 7
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
PCINT22
PCINT14
PRTIM2
PCINT6
REFS0
ACME
ADSC
WDIE
Bit 6
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
PCINT21
PCINT13
PCINT5
PRTIM0
ADLAR
ADATE
WDP3
ICIE1
Bit 5
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
Oscillator Calibration Register
ADC Data Register High byte
ADC Data Register Low byte
PCINT20
PCINT12
PCINT4
WDCE
Bit 4
ADIF
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
PCINT19
PCINT11
CLKPS3
PRTIM1
PCINT3
MUX3
ISC11
ADIE
WDE
Bit 3
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
PCINT18
PCINT10
CLKPS2
OCIE2B
OCIE1B
OCIE0B
PCINT2
ADPS2
ADTS2
PRSPI
PCIE2
WDP2
MUX2
ISC10
Bit 2
–
–
–
–
–
–
–
–
–
–
–
–
–
PRUSART0
PCINT17
CLKPS1
OCIE2A
OCIE1A
OCIE0A
PCINT9
PCINT1
ADPS1
ADTS1
PCIE1
WDP1
MUX1
ISC01
Bit 1
–
–
–
–
–
–
–
–
–
–
–
–
–
PCINT16
CLKPS0
PCINT8
PCINT0
PRADC
ADTS0
ADPS0
MUX0
TOIE2
TOIE1
TOIE0
ISC00
PCIE0
WDP0
Bit 0
–
–
–
–
–
–
–
–
–
–
–
–
–
9111H–AUTO–01/11
Page
277
281
278
280
280
179
160
130
112
112
112
109
58
66
61
78