PIC18F46J50-I/PT Microchip Technology, PIC18F46J50-I/PT Datasheet - Page 112

• Manufacturer Part Number: PIC18F46J50-I/PT
• Description: IC PIC MCU FLASH 64KB 44-TQFP
• Manufacturer: Microchip Technology
• Series: PIC® XLP™ 18Fr

Specifications of PIC18F46J50-I/PT

• Core Size: 8-Bit
• Program Memory Size: 64KB (32K x 16)
• Core Processor: PIC
• Speed: 48MHz
• Connectivity: I²C, SPI, UART/USART, USB
• Peripherals: Brown-out Detect/Reset, DMA, POR, PWM, WDT
• Number Of I /o: 34
• Program Memory Type: FLASH
• Ram Size: 3.8K x 8
• Voltage - Supply (vcc/vdd): 2.15 V ~ 3.6 V
• Data Converters: A/D 13x10b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 44-TQFP, 44-VQFP
• Controller Family/series: PIC18
• No. Of I/o's: 22
• Ram Memory Size: 3.6875KB
• Cpu Speed: 48MHz
• No. Of Timers: 2
• No. Of Pwm Channels: 2
• Package: 44TQFP
• Device Core: PIC
• Family Name: PIC18
• Maximum Speed: 48 MHz
• Operating Supply Voltage: 2.5|3.3 V
• Data Bus Width: 8 Bit
• Interface Type: I2C/SPI/USART/USB
• On-chip Adc: 13-chx10-bit
• Number Of Timers: 5
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• For Use With: AC164330 - MODULE SKT FOR 44TQFP 18F45J10
• Eeprom Size: -
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant, Lead free / RoHS Compliant

PIC18F46J50 FAMILY
REGISTER 8-2:
DS39931C-page 112
bit 7
Legend:
R = Readable bit
-n = Value at POR
bit 7
bit 6
bit 5
bit 4
bit 3
bit 2
bit 1
bit 0
Note:
R/W-1
RBPU
Interrupt flag bits are set when an interrupt condition occurs regardless of the state of its corresponding
enable bit or the global interrupt enable bit. User software should ensure the appropriate interrupt flag bits
are clear prior to enabling an interrupt. This feature allows for software polling.
RBPU: PORTB Pull-up Enable bit
1 = All PORTB pull-ups are disabled
0 = PORTB pull-ups are enabled by individual port latch values
INTEDG0: External Interrupt 0 Edge Select bit
1 = Interrupt on rising edge
0 = Interrupt on falling edge
INTEDG1: External Interrupt 1 Edge Select bit
1 = Interrupt on rising edge
0 = Interrupt on falling edge
INTEDG2: External Interrupt 2 Edge Select bit
1 = Interrupt on rising edge
0 = Interrupt on falling edge
INTEDG3: External Interrupt 3 Edge Select bit
1 = Interrupt on rising edge
0 = Interrupt on falling edge
TMR0IP: TMR0 Overflow Interrupt Priority bit
1 = High priority
0 = Low priority
INT3IP: INT3 External Interrupt Priority bit
1 = High priority
0 = Low priority
RBIP: RB Port Change Interrupt Priority bit
1 = High priority
0 = Low priority
INTEDG0
R/W-1
INTCON2: INTERRUPT CONTROL REGISTER 2 (ACCESS FF1h)
W = Writable bit
‘1’ = Bit is set
INTEDG1
R/W-1
INTEDG2
R/W-1
U = Unimplemented bit, read as ‘0’
‘0’ = Bit is cleared
INTEDG3
R/W-1
TMR0IP
R/W-1
© 2009 Microchip Technology Inc.
x = Bit is unknown
INT3IP
R/W-1
R/W-1
RBIP
bit 0