PIC18F46J50-I/PT Microchip Technology, PIC18F46J50-I/PT Datasheet - Page 125

• Manufacturer Part Number: PIC18F46J50-I/PT
• Description: IC PIC MCU FLASH 64KB 44-TQFP
• Manufacturer: Microchip Technology
• Series: PIC® XLP™ 18Fr

Specifications of PIC18F46J50-I/PT

• Core Size: 8-Bit
• Program Memory Size: 64KB (32K x 16)
• Core Processor: PIC
• Speed: 48MHz
• Connectivity: I²C, SPI, UART/USART, USB
• Peripherals: Brown-out Detect/Reset, DMA, POR, PWM, WDT
• Number Of I /o: 34
• Program Memory Type: FLASH
• Ram Size: 3.8K x 8
• Voltage - Supply (vcc/vdd): 2.15 V ~ 3.6 V
• Data Converters: A/D 13x10b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 44-TQFP, 44-VQFP
• Controller Family/series: PIC18
• No. Of I/o's: 22
• Ram Memory Size: 3.6875KB
• Cpu Speed: 48MHz
• No. Of Timers: 2
• No. Of Pwm Channels: 2
• Package: 44TQFP
• Device Core: PIC
• Family Name: PIC18
• Maximum Speed: 48 MHz
• Operating Supply Voltage: 2.5|3.3 V
• Data Bus Width: 8 Bit
• Interface Type: I2C/SPI/USART/USB
• On-chip Adc: 13-chx10-bit
• Number Of Timers: 5
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• For Use With: AC164330 - MODULE SKT FOR 44TQFP 18F45J10
• Eeprom Size: -
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant, Lead free / RoHS Compliant

9.0
Depending on the device selected and features
enabled, there are up to five ports available. Some pins
of the I/O ports are multiplexed with an alternate
function from the peripheral features on the device. In
general, when a peripheral is enabled, that pin may not
be used as a general purpose I/O pin.
Each port has three registers for its operation. These
registers are:
• TRIS register (Data Direction register)
• PORT register (reads the levels on the pins of the
• LAT register (Data Latch)
The Data Latch (LAT register) is useful for read-modify-
write operations on the value that the I/O pins are
driving.
Figure 9-1 displays a simplified model of a generic I/O
port, without the interfaces to other peripherals.
FIGURE 9-1:
© 2009 Microchip Technology Inc.
device)
RD LAT
Data
Bus
WR LAT
or PORT
WR TRIS
RD TRIS
RD PORT
Note 1: I/O pins have diode protection to V
I/O PORTS
V
SS
TRIS Latch
Data Latch
D
D
CK
CK
.
GENERIC I/O PORT
OPERATION
Q
Q
Q
EN
EN
D
I/O pin
Buffer
Input
DD
and
(1)
PIC18F46J50 FAMILY
9.1
When developing an application, the capabilities of the
port pins must be considered. Outputs on some pins
have higher output drive strength than others. Similarly,
some pins can tolerate higher than V
9.1.1
The output pin drive strengths vary for groups of pins
intended to meet the needs for a variety of applications.
PORTB and PORTC are designed to drive higher
loads, such as LEDs. All other ports are designed for
small loads, typically indication only. Table 9-1 sum-
marizes the output capabilities. Refer to Section 29.0
“Electrical Characteristics” for more details.
TABLE 9-1:
9.1.2
The voltage tolerance of pins used as device inputs is
dependent on the pin’s input function. Pins that are used
as digital only inputs are able to handle DC voltages up
to 5.5V; a level typical for digital logic circuits. In contrast,
pins that also have analog input functions of any kind
can only tolerate voltages up to V
beyond V
summarizes
Section 29.0 “Electrical Characteristics” for more
details.
TABLE 9-2:
PORTA
PORTD
PORTE
PORTB
PORTC
PORTA<7:0>
PORTB<3:0>
PORTC<2:0>
PORTE<2:0>
PORTB<7:4>
PORTC<7:6>
PORTD<7:0>
PORTC<5:4>
Port or Pin
Port
I/O Port Pin Capabilities
DD
PIN OUTPUT DRIVE
INPUT PINS AND VOLTAGE
CONSIDERATIONS
on these pins should be avoided. Table 9-2
Minimum Intended for indication.
the
Drive
High
Tolerated
OUTPUT DRIVE LEVELS
INPUT VOLTAGE LEVELS
(USB)
Input
5.5V
V
input
DD
Suitable for direct LED drive
levels.
capabilities.
Only V
tolerated.
Tolerates input levels
above V
most standard logic.
Designed for USB
specifications.
DD
Description
. Voltage excursions
DS39931C-page 125
Description
DD
DD
DD
input levels.
input levels
, useful for
Refer
to