PIC18F46J50-I/PT Microchip Technology, PIC18F46J50-I/PT Datasheet - Page 290

• Manufacturer Part Number: PIC18F46J50-I/PT
• Description: IC PIC MCU FLASH 64KB 44-TQFP
• Manufacturer: Microchip Technology
• Series: PIC® XLP™ 18Fr

Specifications of PIC18F46J50-I/PT

• Core Size: 8-Bit
• Program Memory Size: 64KB (32K x 16)
• Core Processor: PIC
• Speed: 48MHz
• Connectivity: I²C, SPI, UART/USART, USB
• Peripherals: Brown-out Detect/Reset, DMA, POR, PWM, WDT
• Number Of I /o: 34
• Program Memory Type: FLASH
• Ram Size: 3.8K x 8
• Voltage - Supply (vcc/vdd): 2.15 V ~ 3.6 V
• Data Converters: A/D 13x10b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 44-TQFP, 44-VQFP
• Controller Family/series: PIC18
• No. Of I/o's: 22
• Ram Memory Size: 3.6875KB
• Cpu Speed: 48MHz
• No. Of Timers: 2
• No. Of Pwm Channels: 2
• Package: 44TQFP
• Device Core: PIC
• Family Name: PIC18
• Maximum Speed: 48 MHz
• Operating Supply Voltage: 2.5|3.3 V
• Data Bus Width: 8 Bit
• Interface Type: I2C/SPI/USART/USB
• On-chip Adc: 13-chx10-bit
• Number Of Timers: 5
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• For Use With: AC164330 - MODULE SKT FOR 44TQFP 18F45J10
• Eeprom Size: -
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant, Lead free / RoHS Compliant

PIC18F46J50 FAMILY
18.5.3.5
When the R/W bit of the address byte is clear and an
address match occurs, the R/W bit of the SSPxSTAT
register is cleared. The received address is loaded into
the SSPxBUF register and the SDAx line is held low
(ACK).
When the address byte overflow condition exists, then
the no Acknowledge (ACK) pulse is given. An overflow
condition is defined as either bit, BF (SSPxSTAT<0>),
is set or bit, SSPOV (SSPxCON1<6>), is set.
An MSSP interrupt is generated for each data transfer
byte. The interrupt flag bit, SSPxIF, must be cleared in
software. The SSPxSTAT register is used to determine
the status of the byte.
If SEN is enabled (SSPxCON2<0> = 1), SCLx will be
held low (clock stretch) following each data transfer.
The clock must be released by setting bit, CKP
(SSPxCON1<4>).
Stretching” for more details.
DS39931C-page 290
Reception
See
Section 18.5.4
“Clock
18.5.3.6
When the R/W bit of the incoming address byte is set
and an address match occurs, the R/W bit of the
SSPxSTAT register is set. The received address is
loaded into the SSPxBUF register. The ACK pulse will
be sent on the ninth bit and pin SCLx is held low regard-
less of SEN (see Section 18.5.4 “Clock Stretching”
for more details). By stretching the clock, the master
will be unable to assert another clock pulse until the
slave is done preparing the transmit data. The transmit
data must be loaded into the SSPxBUF register, which
also loads the SSPxSR register. Then, the SCLx pin
should
(SSPxCON1<4>). The eight data bits are shifted out on
the falling edge of the SCLx input. This ensures that the
SDAx signal is valid during the SCLx high time
(Figure 18-10).
The ACK pulse from the master-receiver is latched on
the rising edge of the ninth SCLx input pulse. If the
SDAx line is high (not ACK), then the data transfer is
complete. In this case, when the ACK is latched by the
slave, the slave logic is reset (resets the SSPxSTAT
register) and the slave monitors for another occurrence
of the Start bit. If the SDAx line was low (ACK), the next
transmit data must be loaded into the SSPxBUF
register. Again, the SCLx pin must be enabled by
setting bit, CKP.
An MSSP interrupt is generated for each data transfer
byte. The SSPxIF bit must be cleared in software and
the SSPxSTAT register is used to determine the status
of the byte. The SSPxIF bit is set on the falling edge of
the ninth clock pulse.
be
Transmission
enabled
© 2009 Microchip Technology Inc.
by
setting
bit,
CKP