PIC18F46J50-I/PT Microchip Technology, PIC18F46J50-I/PT Datasheet - Page 120

• Manufacturer Part Number: PIC18F46J50-I/PT
• Description: IC PIC MCU FLASH 64KB 44-TQFP
• Manufacturer: Microchip Technology
• Series: PIC® XLP™ 18Fr

Specifications of PIC18F46J50-I/PT

• Core Size: 8-Bit
• Program Memory Size: 64KB (32K x 16)
• Core Processor: PIC
• Speed: 48MHz
• Connectivity: I²C, SPI, UART/USART, USB
• Peripherals: Brown-out Detect/Reset, DMA, POR, PWM, WDT
• Number Of I /o: 34
• Program Memory Type: FLASH
• Ram Size: 3.8K x 8
• Voltage - Supply (vcc/vdd): 2.15 V ~ 3.6 V
• Data Converters: A/D 13x10b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 44-TQFP, 44-VQFP
• Controller Family/series: PIC18
• No. Of I/o's: 22
• Ram Memory Size: 3.6875KB
• Cpu Speed: 48MHz
• No. Of Timers: 2
• No. Of Pwm Channels: 2
• Package: 44TQFP
• Device Core: PIC
• Family Name: PIC18
• Maximum Speed: 48 MHz
• Operating Supply Voltage: 2.5|3.3 V
• Data Bus Width: 8 Bit
• Interface Type: I2C/SPI/USART/USB
• On-chip Adc: 13-chx10-bit
• Number Of Timers: 5
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• For Use With: AC164330 - MODULE SKT FOR 44TQFP 18F45J10
• Eeprom Size: -
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant, Lead free / RoHS Compliant

PIC18F46J50 FAMILY
8.4
The IPR registers contain the individual priority bits for
the peripheral interrupts. Due to the number of
peripheral interrupt sources, there are three Peripheral
Interrupt Priority registers (IPR1, IPR2, IPR3). Using
the priority bits requires that the Interrupt Priority
Enable (IPEN) bit be set.
REGISTER 8-10:
DS39931C-page 120
bit 7
Legend:
R = Readable bit
-n = Value at POR
bit 7
bit 6
bit 5
bit 4
bit 3
bit 2
bit 1
bit 0
Note 1:
PMPIP
R/W-1
IPR Registers
(1)
These bits are unimplemented on 28-pin devices.
PMPIP: Parallel Master Port Read/Write Interrupt Priority bit
1 = High priority
0 = Low priority
ADIP: A/D Converter Interrupt Priority bit
1 = High priority
0 = Low priority
RC1IP: EUSART1 Receive Interrupt Priority bit
1 = High priority
0 = Low priority
TX1IP: EUSART1 Transmit Interrupt Priority bit
1 = High priority
0 = Low priority
SSP1IP: Master Synchronous Serial Port Interrupt Priority bit (MSSP1 module)
1 = High priority
0 = Low priority
CCP1IP: ECCP1 Interrupt Priority bit
1 = High priority
0 = Low priority
TMR2IP: TMR2 to PR2 Match Interrupt Priority bit
1 = High priority
0 = Low priority
TMR1IP: TMR1 Overflow Interrupt Priority bit
1 = High priority
0 = Low priority
R/W-1
ADIP
IPR1: PERIPHERAL INTERRUPT PRIORITY REGISTER 1 (ACCESS F9Fh)
W = Writable bit
‘1’ = Bit is set
RC1IP
R/W-1
R/W-1
TX1IP
U = Unimplemented bit, read as ‘0’
‘0’ = Bit is cleared
SSP1IP
R/W-1
(1)
CCP1IP
R/W-1
© 2009 Microchip Technology Inc.
x = Bit is unknown
TMR2IP
R/W-1
TMR1IP
R/W-1
bit 0