PIC18F46J50-I/PT Microchip Technology, PIC18F46J50-I/PT Datasheet - Page 141

• Manufacturer Part Number: PIC18F46J50-I/PT
• Description: IC PIC MCU FLASH 64KB 44-TQFP
• Manufacturer: Microchip Technology
• Series: PIC® XLP™ 18Fr

Specifications of PIC18F46J50-I/PT

• Core Size: 8-Bit
• Program Memory Size: 64KB (32K x 16)
• Core Processor: PIC
• Speed: 48MHz
• Connectivity: I²C, SPI, UART/USART, USB
• Peripherals: Brown-out Detect/Reset, DMA, POR, PWM, WDT
• Number Of I /o: 34
• Program Memory Type: FLASH
• Ram Size: 3.8K x 8
• Voltage - Supply (vcc/vdd): 2.15 V ~ 3.6 V
• Data Converters: A/D 13x10b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 44-TQFP, 44-VQFP
• Controller Family/series: PIC18
• No. Of I/o's: 22
• Ram Memory Size: 3.6875KB
• Cpu Speed: 48MHz
• No. Of Timers: 2
• No. Of Pwm Channels: 2
• Package: 44TQFP
• Device Core: PIC
• Family Name: PIC18
• Maximum Speed: 48 MHz
• Operating Supply Voltage: 2.5|3.3 V
• Data Bus Width: 8 Bit
• Interface Type: I2C/SPI/USART/USB
• On-chip Adc: 13-chx10-bit
• Number Of Timers: 5
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• For Use With: AC164330 - MODULE SKT FOR 44TQFP 18F45J10
• Eeprom Size: -
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant, Lead free / RoHS Compliant

9.6
Depending on the particular PIC18F46J50 Family
device selected, PORTE is implemented in two
different ways.
For 44-pin devices, PORTE is a 3-bit wide port. Three
pins (RE0/AN5/PMRD, RE1/AN6/PMWR and RE2/
AN7/PMCS) are individually configurable as inputs or
outputs. These pins have Schmitt Trigger input buffers.
When selected as analog inputs, these pins will read as
‘0’s.
The corresponding Data Direction register is TRISE.
Setting a TRISE bit (= 1) will make the corresponding
PORTE pin an input (i.e., put the corresponding output
driver in a high-impedance mode). Clearing a TRISE bit
(= 0) will make the corresponding PORTE pin an output
(i.e., put the contents of the output latch on the selected
pin).
TRISE controls the direction of the RE pins, even when
they are being used as analog inputs. The user must
make sure to keep the pins configured as inputs when
using them as analog inputs.
© 2009 Microchip Technology Inc.
Note:
Note:
PORTE, TRISE and LATE
Registers
PORTE is available only in 44-pin devices.
On a POR, RE<2:0> are configured as
analog inputs.
PIC18F46J50 FAMILY
The Data Latch register (LATE) is also memory
mapped. Read-modify-write operations on the LATE
register read and write the latched output value for
PORTE.
EXAMPLE 9-6:
Each of the PORTE pins has a weak internal pull-up. A
single control bit can turn on all the pull-ups. This is per-
formed by setting bit, REPU (PORTE<6>). The weak
pull-up is automatically turned off when the port pin is
configured as an output. The pull-ups are disabled on a
POR. The integrated weak pull-ups consist of a semi-
conductor structure similar to, but somewhat different,
from a discrete resistor. On an unloaded I/O pin, the
weak pull-ups are intended to provide logic high indica-
tion, but will not necessarily pull the pin all the way to
V
Note that the pull-ups can be used for any set of
features, similar to the pull-ups found on PORTB
CLRF
CLRF
MOVLW
MOVWF
MOVLW
MOVWF
DD
levels.
PORTE
LATE
0Ah
ADCON1
03h
TRISE
; Initialize PORTE by
; clearing output
; data latches
; Alternate method
; to clear output
; data latches
; Configure A/D
; for digital inputs
; Value used to
; initialize data
; direction
; Set RE<0> as inputs
; RE<1> as outputs
; RE<2> as inputs
INITIALIZING PORTE
DS39931C-page 141