PIC18F46J50-I/PT Microchip Technology, PIC18F46J50-I/PT Datasheet - Page 95

• Manufacturer Part Number: PIC18F46J50-I/PT
• Description: IC PIC MCU FLASH 64KB 44-TQFP
• Manufacturer: Microchip Technology
• Series: PIC® XLP™ 18Fr

Specifications of PIC18F46J50-I/PT

• Core Size: 8-Bit
• Program Memory Size: 64KB (32K x 16)
• Core Processor: PIC
• Speed: 48MHz
• Connectivity: I²C, SPI, UART/USART, USB
• Peripherals: Brown-out Detect/Reset, DMA, POR, PWM, WDT
• Number Of I /o: 34
• Program Memory Type: FLASH
• Ram Size: 3.8K x 8
• Voltage - Supply (vcc/vdd): 2.15 V ~ 3.6 V
• Data Converters: A/D 13x10b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 44-TQFP, 44-VQFP
• Controller Family/series: PIC18
• No. Of I/o's: 22
• Ram Memory Size: 3.6875KB
• Cpu Speed: 48MHz
• No. Of Timers: 2
• No. Of Pwm Channels: 2
• Package: 44TQFP
• Device Core: PIC
• Family Name: PIC18
• Maximum Speed: 48 MHz
• Operating Supply Voltage: 2.5|3.3 V
• Data Bus Width: 8 Bit
• Interface Type: I2C/SPI/USART/USB
• On-chip Adc: 13-chx10-bit
• Number Of Timers: 5
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• For Use With: AC164330 - MODULE SKT FOR 44TQFP 18F45J10
• Eeprom Size: -
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant, Lead free / RoHS Compliant

FIGURE 5-9:
© 2009 Microchip Technology Inc.
EXAMPLE INSTRUCTION: ADDWF, f, d, a (Opcode: 0010 01da ffff ffff)
When a = 0 and f ≥ 60h:
The instruction executes in
Direct Forced mode. ‘f’ is
interpreted as a location in the
Access RAM between 060h
and FFFh. This is the same as
locations
(Bank 15) of data memory.
Locations below 060h are not
available in this addressing
mode.
When a = 0 and f ≤ 5Fh:
The instruction executes in
Indexed Literal Offset mode. ‘f’
is interpreted as an offset to the
address value in FSR2. The
two are added together to
obtain the address of the target
register for the instruction. The
address can be anywhere in
the data memory space.
Note that in this mode, the
correct syntax is:
ADDWF [k], d
where ‘k’ is same as ‘f’.
When a = 1 (all values of f):
The instruction executes in
Direct mode (also known as
Direct Long mode). ‘f’ is
interpreted as a location in
one of the 16 banks of the data
memory space. The bank is
designated by the Bank Select
Register (BSR). The address
can be in any implemented
bank in the data memory
space.
F60h
COMPARING ADDRESSING OPTIONS FOR BIT-ORIENTED AND BYTE-ORIENTED
INSTRUCTIONS (EXTENDED INSTRUCTION SET ENABLED)
to
FFFh
FFFh
FFFh
FFFh
000h
060h
100h
F00h
F60h
000h
060h
100h
F00h
F60h
000h
060h
100h
F00h
F60h
Data Memory
Data Memory
Data Memory
Bank 15
Bank 15
Bank 15
Bank 14
Bank 14
Bank 14
Bank 0
through
Bank 0
through
Bank 0
through
PIC18F46J50 FAMILY
Bank 1
Bank 1
Bank 1
SFRs
SFRs
SFRs
001001da
00000000
001001da
BSR
Access RAM
FSR2H
ffffffff
ffffffff
FSR2L
00h
60h
FFh
DS39931C-page 95
Valid range
for ‘f’