HD6432670 Hitachi, HD6432670 Datasheet - Page 749
HD6432670
Manufacturer Part Number
HD6432670
Description
(HD64F267x Series) 16-Bit Microcomputer
Manufacturer
Hitachi
Datasheet
1.HD6432670.pdf
(953 pages)
- Current page: 749 of 953
- Download datasheet (6Mb)
DMAC is not activated, but instead, an ERI interrupt request is sent to the CPU. Therefore, the
error flag should be cleared.
15.10
Usage Notes
15.10.1 Module Stop Mode Setting
SCI operation can be disabled or enabled using the module stop control register. The initial setting
is for SCI operation to be halted. Register access is enabled by clearing module stop mode. For
details, refer to section 22, Power-Down Modes.
15.10.2 Break Detection and Processing
When framing error detection is performed, a break can be detected by reading the RxD pin value
directly. In a break, the input from the RxD pin becomes all 0s, and so the FER flag is set, and the
PER flag may also be set. Note that, since the SCI continues the receive operation after receiving
a break, even if the FER flag is cleared to 0, it will be set to 1 again.
15.10.3 Mark State and Break Sending
When TE is 0, the TxD pin is used as an I/O port whose direction (input or output) and level are
determined by DR and DDR. This can be used to set the TxD pin to mark state or send a break
during serial data transmission. To maintain the communication line at mark state until TE is set
to 1, set both PCR and PDR to 1. Since TE is cleared to 0 at this point, the TxD pin becomes an
I/O port, and 1 is output from the TxD pin. To send a break during serial transmission, first set
PCR to 1 and clear PDR to 0, and then clear TE to 0. When TE is cleared to 0, the transmitter is
initialized regardless of the current transmission state, the TxD pin becomes an I/O port, and 0 is
output from the TxD pin.
15.10.4 Receive Error Flags and Transmit Operations (Clocked Synchronous Mode Only)
Transmission cannot be started when a receive error flag (ORER, PER, or FER) is set to 1, even if
the TDRE flag is cleared to 0. Be sure to clear the receive error flags to 0 before starting
transmission. Note also that receive error flags cannot be cleared to 0 even if the RE bit is cleared
to 0.
15.10.5 Relation between Writes to TDR and the TDRE Flag
The TDRE flag in SSR is a status flag that indicates that transmit data has been transferred from
TDR to TSR. When the SCI transfers data from TDR to TSR, the TDRE flag is set to 1.
Rev. 2.0, 04/02, page 703 of 906
Related parts for HD6432670
Image
Part Number
Description
Manufacturer
Datasheet
Request
R
Part Number:
Description:
Silicon N-Channel Power MOS FET Module
Manufacturer:
HITACHI
Datasheet:
Part Number:
Description:
High Speed Power Switching
Manufacturer:
HITACHI
Datasheet:
Part Number:
Description:
Silicon N-Channel IGBT
Manufacturer:
HITACHI
Datasheet:
Part Number:
Description:
IGBT MODULE RANGE WITH SOFT AND FAST (SFD) FREE-WHEELING DIODES
Manufacturer:
HITACHI
Datasheet:
Part Number:
Description:
IGBT MODULE RANGE WITH SOFT AND FAST (SFD) FREE-WHEELING DIODES
Manufacturer:
HITACHI
Datasheet:
Part Number:
Description:
IGBT MODULE RANGE WITH SOFT AND FAST (SFD) FREE-WHEELING DIODES
Manufacturer:
HITACHI
Datasheet:
Part Number:
Description:
8MHz V(cc): -0.3 to +7.0V V(in): -0.3 to +0.3V advanced CRT controller (ACRTC)
Manufacturer:
HITACHI
Datasheet:
Part Number:
Description:
65,536-WORD x 4-BIT MULTIPORT CMOS VIDEO RAM
Manufacturer:
HITACHI
Datasheet:
Part Number:
Description:
65,536-WORD x 4-BIT MULTIPORT CMOS VIDEO RAM
Manufacturer:
HITACHI
Datasheet:
Part Number:
Description:
65,536-word ? 4-bit High Speed CMOS Static RAM
Manufacturer:
HITACHI
Datasheet:
Part Number:
Description:
SINGLE CHIP CODEC WITH FILTERS(COMBO)
Manufacturer:
HITACHI
Datasheet: