SI4431-A0-FM Silicon Laboratories Inc, SI4431-A0-FM Datasheet - Page 23

• Manufacturer Part Number: SI4431-A0-FM
• Description: IC TXRX ISM 930MHZ 3.6V 20-QFN
• Manufacturer: Silicon Laboratories Inc

Specifications of SI4431-A0-FM

• Package / Case: 20-QFN
• Mfg Application Notes: Transitioning SI4430/31 to Rev B
• Frequency: 240MHz ~ 930MHz
• Data Rate - Maximum: 128kbps
• Modulation Or Protocol: FSK, GFSK, OOK
• Power - Output: 13dBm
• Sensitivity: -118dBm
• Voltage - Supply: 1.8 V ~ 3.6 V
• Current - Receiving: 18.5mA
• Current - Transmitting: 28mA
• Data Interface: PCB, Surface Mount
• Antenna Connector: PCB, Surface Mount
• Operating Temperature: -40°C ~ 85°C
• Number Of Receivers: 2
• Number Of Transmitters: 1
• Wireless Frequency: 240 MHz to 930 MHz
• Output Power: 13 dBm
• Operating Supply Voltage: 1.8 V to 3.6 V
• Maximum Operating Temperature: + 85 C
• Mounting Style: SMD/SMT
• Maximum Supply Current: 28 mA
• Minimum Operating Temperature: - 40 C
• Modulation: FSK, GFSK, OOK
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Applications: -
• Memory Size: -
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant, Lead free / RoHS Compliant
• Other names: 336-1633-5

Si4431
3.2.3. TX State
The TX state may be entered from any of the IDLE modes when the txon bit is set to 1 in "Register 07h. Operating
Mode and Function Control 1". A built-in sequencer takes care of all the actions required to transition between
states from enabling the crystal oscillator to ramping up the PA to prevent unwanted spectral splatter. The following
sequence of events will occur automatically when going from STANDBY mode to TX mode by setting the txon bit.
1. Enable the Main Digital LDO and the Analog LDOs.
2. Start up crystal oscillator and wait until ready (controlled by timer).
3. Enable PLL.
4. Calibrate VCO (this action is skipped when the vcocal bit is “0”, default value is “1”).
5. Wait until PLL settles to required transmit frequency (controlled by timer).
6. Activate Power Amplifier and wait until power ramping is completed (controlled by timer).
7. Transmit Packet.
The first few steps may be eliminated depending on which IDLE mode the chip is configured to prior to setting the
txon bit. By default, the VCO and PLL are calibrated every time the PLL is enabled. If the ambient temperature is
constant and the same frequency band is being used these functions may be skipped by setting the appropriate
bits in "Register 55h. Calibration Control".
3.2.4. RX State
The RX state may be entered from any of the Idle modes when the rxon bit is set to 1 in "Register 07h. Operating
Mode and Function Control 1". A built-in sequencer takes care of all the actions required to transition from one of
the IDLE modes to the RX state. The following sequence of events will occur automatically to get the chip into RX
mode when going from STANDBY mode to RX mode by setting the rxon bit:
1. Enable the Main Digital LDO and the Analog LDOs.
2. Start up crystal oscillator and wait until ready (controlled by timer).
3. Enable PLL.
4. Calibrate VCO (this action is skipped when the vcocal bit is “0”, default value is “1”).
5. Wait until PLL settles to required transmit frequency (controlled by timer).
6. Enable receive circuits: LNA, mixers, and ADC.
7. Calibrate ADC (RC calibration).
8. Enable receive mode in the digital modem.
Depending on the configuration of the radio all or some of the following functions will be performed automatically by
the digital modem: AGC, AFC (optional), update status registers, bit synchronization, packet handling (optional)
including sync word, header check, and CRC.
3.2.5. Device Status
Add R/W Function/Description
D7
D6
D5
D4
D3
D2
D1
D0
POR Def.
02
R
Device Status
ffovfl
ffunfl
rxffem
headerr
cps[1] cps[0]
—
The operational status of the chip can be read from "Register 02h. Device Status".
Preliminary Rev. 0.4
23