SI4431-A0-FM Silicon Laboratories Inc, SI4431-A0-FM Datasheet - Page 29

• Manufacturer Part Number: SI4431-A0-FM
• Description: IC TXRX ISM 930MHZ 3.6V 20-QFN
• Manufacturer: Silicon Laboratories Inc

Specifications of SI4431-A0-FM

• Package / Case: 20-QFN
• Mfg Application Notes: Transitioning SI4430/31 to Rev B
• Frequency: 240MHz ~ 930MHz
• Data Rate - Maximum: 128kbps
• Modulation Or Protocol: FSK, GFSK, OOK
• Power - Output: 13dBm
• Sensitivity: -118dBm
• Voltage - Supply: 1.8 V ~ 3.6 V
• Current - Receiving: 18.5mA
• Current - Transmitting: 28mA
• Data Interface: PCB, Surface Mount
• Antenna Connector: PCB, Surface Mount
• Operating Temperature: -40°C ~ 85°C
• Number Of Receivers: 2
• Number Of Transmitters: 1
• Wireless Frequency: 240 MHz to 930 MHz
• Output Power: 13 dBm
• Operating Supply Voltage: 1.8 V to 3.6 V
• Maximum Operating Temperature: + 85 C
• Mounting Style: SMD/SMT
• Maximum Supply Current: 28 mA
• Minimum Operating Temperature: - 40 C
• Modulation: FSK, GFSK, OOK
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Applications: -
• Memory Size: -
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant, Lead free / RoHS Compliant
• Other names: 336-1633-5

3.6.2. Easy Frequency Programming for FHSS
While Registers 73h–77h may be used to program the carrier frequency of the Si4431, it is often easier to think in
terms of “channels” or “channel numbers” rather than an absolute frequency value in Hz. Also, there may be some
timing-critical applications (such as for Frequency Hopping Systems) in which it is desirable to change frequency
by programming a single register. Once the channel step size is set, the frequency may be changed by a single
register corresponding to the channel number. A nominal frequency is first set using Registers 73h–77h, as
described above. Registers 79h and 7Ah are then used to set a channel step size and channel number, relative to
the nominal setting. The Frequency Hopping Step Size (fhs[7:0]) is set in increments of 10 kHz with a maximum
channel step size of 2.56 MHz. The Frequency Hopping Channel Select Register then selects channels based on
multiples of the step size.
For example: if the nominal frequency is set to 900 MHz using Registers 73h–77h and the channel step size is set
to 1 MHz using "Register 7Ah. Frequency Hopping Step Size". For example, if the "Register 79h. Frequency
Hopping Channel Select" is set to 5d, the resulting carrier frequency would be 905 MHz. Once the nominal
frequency and channel step size are programmed in the registers, it is only necessary to program the fhch[7:0]
register in order to change the frequency.
3.6.3. Automatic Frequency Change
If registers 79h or 7Ah are changed in either TX or mode, the state machine will automatically transition the chip
back to tune, change the frequency, and automatically go back to either TX or RX. This feature is useful to reduce
the number of SPI commands required in a Frequency Hopping System. This in turn reduces microcontroller
activity, reducing current consumption.
3.6.4. Frequency Deviation
The peak frequency deviation is configurable from ±1 to ±320 kHz. The Frequency Deviation (Δf) is controlled by
the Frequency Deviation Register (fd), address 71 and 72h, and is independent of the carrier frequency setting.
When enabled, regardless of the setting of the hbsel bit (high band or low band), the resolution of the frequency
deviation will remain in increments of 625 Hz. When using frequency modulation the carrier frequency will deviate
from the nominal center channel carrier frequency by ±Δf:
Add R/W
79
7A
R/W Frequency Hopping Channel
R/W
Function/Description
Frequency Hopping Step
Select
Size
F
carrier
fd

[
: 8
Fnom
fhch[7] fhch[6] fhch[5] fhch[4] fhch[3] fhch[2] fhch[1] fhch[0]
fhs[7]
D7
] 0



f
625
Preliminary Rev. 0.4
fhs
fhs[6]


D6
f
Hz
[
fd
: 7
[
: 8
] 0
fhs[5]
 f
] 0

D5
(

fhch
=
625
peak deviation
fhs[4]
[
D4
Hz
: 7
] 0

fhs[3]
10
D3
kHz
)
fhs[2]
D2
fhs[1]
D1
fhs[0]
Si4431
D0
POR Def.
00h
00h
29