S912XET256J2VAGR Freescale Semiconductor, S912XET256J2VAGR Datasheet - Page 979

• Manufacturer Part Number: S912XET256J2VAGR
• Description: 16-bit Microcontrollers - MCU Watchdog OSC/Timer -40 C to + 105 C HCS12X MCU SPI
• Manufacturer: Freescale Semiconductor

Specifications of S912XET256J2VAGR

• Core: HCS12X
• Data Bus Width: 16 bit
• Maximum Clock Frequency: 50 MHz
• Program Memory Size: 256 KB
• Data Ram Size: 16 KB
• On-chip Adc: Yes
• Package / Case: LQFP
• Mounting Style: SMD/SMT
• A/d Bit Size: 12 bit
• A/d Channels Available: 24
• Interface Type: CAN, SCI, SPI
• Maximum Operating Temperature: + 105 C
• Minimum Operating Temperature: - 40 C
• Number Of Programmable I/os: 119
• Number Of Timers: 25
• Program Memory Type: Flash
• Supply Voltage - Max: 1.98 V, 2.9 V, 5.5 V
• Supply Voltage - Min: 1.72 V, 2.7 V, 3.13 V

26.3.2.11.1 FCCOB - NVM Command Mode
NVM command mode uses the indexed FCCOB register to provide a command code and its relevant
parameters to the Memory Controller. The user first sets up all required FCCOB fields and then initiates
the command’s execution by writing a 1 to the CCIF bit in the FSTAT register (a 1 written by the user
clears the CCIF command completion flag to 0). When the user clears the CCIF bit in the FSTAT register
all FCCOB parameter fields are locked and cannot be changed by the user until the command completes
(as evidenced by the Memory Controller returning CCIF to 1). Some commands return information to the
FCCOB register array.
The generic format for the FCCOB parameter fields in NVM command mode is shown in
The return values are available for reading after the CCIF flag in the FSTAT register has been returned to
1 by the Memory Controller. Writes to the unimplemented parameter fields (CCOBIX = 110 and CCOBIX
= 111) are ignored with reads from these fields returning 0x0000.
Table 26-26
contains the command code, followed by the parameters for this specific Flash command. For details on
the FCCOB settings required by each command, see the Flash command descriptions in
Freescale Semiconductor
Offset Module Base + 0x000A
Offset Module Base + 0x000B
Reset
Reset
W
W
R
R
shows the generic Flash command format. The high byte of the first word in the CCOB array
0
0
7
7
Figure 26-17. Flash Common Command Object Low Register (FCCOBLO)
Figure 26-16. Flash Common Command Object High Register (FCCOBHI)
CCOBIX[2:0]
000
001
010
Table 26-26. FCCOB - NVM Command Mode (Typical Usage)
0
0
6
6
MC9S12XE-Family Reference Manual Rev. 1.25
Byte
LO
LO
LO
HI
HI
HI
0
0
5
5
FCCOB Parameter Fields (NVM Command Mode)
FCMD[7:0] defining Flash command
0
0
4
4
CCOB[15:8]
CCOB[7:0]
0, Global address [22:16]
Global address [15:8]
Global address [7:0]
Data 0 [15:8]
Data 0 [7:0]
Chapter 26 384 KByte Flash Module (S12XFTM384K2V1)
0
0
3
3
0
0
2
2
0
0
1
1
Section
Table
26-26.
26.4.2.
0
0
0
0
979