C8051F930-TB Silicon Laboratories Inc, C8051F930-TB Datasheet - Page 167

• Manufacturer Part Number: C8051F930-TB
• Description: BOARD TARGET/PROTO W/C8051F930
• Manufacturer: Silicon Laboratories Inc
• Type: MCUr

Specifications of C8051F930-TB

• Contents: Board
• Processor To Be Evaluated: C8051F930
• Processor Series: C8051F9xx
• Data Bus Width: 8 bit
• Interface Type: I2C, UART, SPI
• Maximum Operating Temperature: + 85 C
• Minimum Operating Temperature: - 40 C
• Operating Supply Voltage: 0.9 V to 3.6 V
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• For Use With/related Products: C8051F930
• Lead Free Status / Rohs Status: Lead free / RoHS Compliant
• Other names: 336-1472

SFR Definition 15.1. CRC0CN: CRC0 Control
SFR Page = 0xF; SFR Address = 0x92
Note: Upon initiation of an automatic CRC calculation, the third opcode byte fetched from program memory is
Reset
Name
Bit
7:5
1:0 CRC0PNT[1:0] CRC0 Result Pointer.
Type
4
3
2
Bit
indeterminate. Therefore, writes to CRC0CN that initiate a CRC operation must be immediately followed by a
benign 3-byte instruction whose third byte is a don’t care. An example of such an instruction is a 3-byte MOV
that targets the CRC0FLIP register. When programming in ‘C’, the dummy value written to CRC0FLIP should
be a non-zero value to prevent the compiler from generating a 2-byte MOV instruction.
CRC0SEL
CRC0INIT
CRC0VAL
Unused
Name
R/W
7
0
Unused.
Read = 000b; Write = Don’t Care.
CRC0 Polynomial Select Bit.
This bit selects the CRC0 polynomial and result length (32-bit or 16-bit).
0: CRC0 uses the 32-bit polynomial 0x04C11DB7 for calculating the CRC result.
1: CRC0 uses the 16-bit polynomial 0x1021 for calculating the CRC result.
CRC0 Result Initialization Bit.
Writing a 1 to this bit initializes the entire CRC result based on CRC0VAL.
CRC0 Set Value Initialization Bit.
This bit selects the set value of the CRC result.
0: CRC result is set to 0x00000000 on write of 1 to CRC0INIT.
1: CRC result is set to 0xFFFFFFFF on write of 1 to CRC0INIT.
Specifies the byte of the CRC result to be read/written on the next access to
CRC0DAT. The value of these bits will auto-increment upon each read or write.
For CRC0SEL = 0:
00: CRC0DAT accesses bits 7–0 of the 32-bit CRC result.
01: CRC0DAT accesses bits 15–8 of the 32-bit CRC result.
10: CRC0DAT accesses bits 23–16 of the 32-bit CRC result.
11: CRC0DAT accesses bits 31–24 of the 32-bit CRC result.
For CRC0SEL = 1:
00: CRC0DAT accesses bits 7–0 of the 16-bit CRC result.
01: CRC0DAT accesses bits 15–8 of the 16-bit CRC result.
10: CRC0DAT accesses bits 7–0 of the 16-bit CRC result.
11: CRC0DAT accesses bits 15–8 of the 16-bit CRC result.
R/W
0
6
R/W
5
0
CRC0SEL CRC0INIT CRC0VAL
R/W
Rev. 1.1
4
0
C8051F93x-C8051F92x
Function
R/W
3
0
R/W
2
0
CRC0PNT[1:0]
1
0
R/W
0
0
167