AT32UC3C1512C Automotive Atmel Corporation, AT32UC3C1512C Automotive Datasheet - Page 892
AT32UC3C1512C Automotive
Manufacturer Part Number
AT32UC3C1512C Automotive
Description
Manufacturer
Atmel Corporation
Datasheets
1.AT90CAN128_AUTOMOTIVE.pdf
(225 pages)
2.AT32UC3C0512C_AUTOMOTIVE.pdf
(1312 pages)
3.AT32UC3C0512C_AUTOMOTIVE.pdf
(107 pages)
- AT90CAN128_AUTOMOTIVE PDF datasheet
- AT32UC3C0512C_AUTOMOTIVE PDF datasheet #2
- AT32UC3C0512C_AUTOMOTIVE PDF datasheet #3
- Current page: 892 of 1312
- Download datasheet (20Mb)
32.6.3.4
32.6.3.5
32.6.3.6
9166C–AVR-08/11
USB reset
Pipe activation
Address setup
Figure 32-17. USB Communication Flow
In host mode, the USBC associates a pipe to a device endpoint, according to the device config-
uration descriptors.
The USBC sends a USB reset signal when the user writes a one to the Send USB Reset bit
(UHCON.RESET). When the USB reset has been sent, the USB Reset Sent Interrupt bit in the
Host Global Interrupt register (UHINT.RSTI) is set and all the pipes will be disabled.
If the bus was previously in a suspended state (UHCON.SOFE is zero) the USBC will switch it to
the Resume state, causing the bus to asynchronously trigger the Host Wakeup Interrupt
(UHINT.HWUPI). The SOFE bit will be set in order to generate SOF’s immediately after the USB
reset.
A disabled pipe is inactive, and will be reset along with its context registers (UPCONn, UPSTAn,
UPINRQn, and UPCFGn). Enabling a pipe is done by writing a one to the Pipe n Enable bit in
the Pipe Enable/Reset Register (UPRST.PENn).
When starting an enumeration, the user gets the device descriptor by sending an
GET_DESCRIPTOR USB request. This descriptor contains the maximal packet size of the
device default control endpoint (bMaxPacketSize0) which the user should use to reconfigure the
size of the default control pipe.
Once the device has answered the first host requests with the default device address 0, the host
assigns a new address to the device. The host controller has to send a USB reset to the device
and a SET_ADDRESS(addr) SETUP request with the new address to be used by the device.
Once this SETUP transaction is over, the user writes to the device address field in the “control
a n d s t a t u s 1 o f e n d p o i n t n ” w o r d o f t h e h o s t ’ s p i p e n i n t h e U S B d e s c r i p t o r
(Pn_CTR_STA1.PDADDR). All following requests by this pipe will be performed using this new
address.
AT32UC3C
892
Related parts for AT32UC3C1512C Automotive
Image
Part Number
Description
Manufacturer
Datasheet
Request
R
Part Number:
Description:
Manufacturer:
Atmel Corporation
Datasheet:
Part Number:
Description:
INTERVAL AND WIPE/WASH WIPER CONTROL IC WITH DELAY
Manufacturer:
ATMEL Corporation
Datasheet:
Part Number:
Description:
Low-Voltage Voice-Switched IC for Hands-Free Operation
Manufacturer:
ATMEL Corporation
Datasheet:
Part Number:
Description:
MONOLITHIC INTEGRATED FEATUREPHONE CIRCUIT
Manufacturer:
ATMEL Corporation
Datasheet:
Part Number:
Description:
AM-FM Receiver IC U4255BM-M
Manufacturer:
ATMEL Corporation
Datasheet:
Part Number:
Description:
Monolithic Integrated Feature Phone Circuit
Manufacturer:
ATMEL Corporation
Datasheet:
Part Number:
Description:
Multistandard Video-IF and Quasi Parallel Sound Processing
Manufacturer:
ATMEL Corporation
Datasheet:
Part Number:
Description:
High-performance EE PLD
Manufacturer:
ATMEL Corporation
Datasheet:
Part Number:
Description:
8-bit Flash Microcontroller
Manufacturer:
ATMEL Corporation
Datasheet:
Part Number:
Description:
2-Wire Serial EEPROM
Manufacturer:
ATMEL Corporation
Datasheet: